Platinum-tungsten and platinum-copper alloys Pt-W, Pt-Cu
Pt-8W: platinum with 8 % tungsten by mass (Pt92/W8). Pt-Cu: carbon-supported PtCux nanoparticles, x = 1.3 by XRF before activation
Also known as PtW8, Hera 158
Platinum-tungsten is a ductile precious-metal alloy.
Evidence level
2 of 5
Lab-measured
- 0Predicted only. No one has made it, or no measurement exists.
- 1Calculated. Only calculated or predicted values from sources.
- 2Lab-measured. Measured properties with their conditions stated.
- 3Space-relevant tests. Measured in conditions relevant to space, such as vacuum or atomic oxygen.
- 4Ground-qualified. Qualified for an application on the ground.
- 5Flown or field-proven. Flight or field results exist.
Density
21.26 g/cm3
Melting
1865 to 1885 °C
Hardness
200 to 300 HV
Catalyst activity
1236 A/g(Pt)
Recipe, share of the weight
- Pt 92%Platinum
- W 8%Tungsten
Best for
Fine resistance wire, probes and electrodes that must resist oxidation in air at high temperature (Pt-W), and dealloyed PtCu catalysts in acid electrolyte (Pt-Cu, laboratory).
Weakest at
Density (21.26 g/cm3) and conductivity (2.58 to 2.77 % IACS, a poor conductor). The PtCu catalyst loses much of its copper in acid.
Risk at a glance
- People Low. Mixed element records
- If it fails Moderate. Copper loss from the PtCu catalyst surface in acid
- Corrosion Moderate. Copper leaves the PtCu/C surface during activation in acid, and the copper content falls.
Quick facts: Pt-W, Pt-Cu
| Property | Value | Basis |
|---|---|---|
| Density | 21.3 g/cm³ | 2 sourced values across conditions |
| Yield strength | 400 to 1,000 MPa | 1 sourced value |
| Tensile strength | 800 to 1,100 MPa | 1 sourced value |
| Young's modulus | 230 GPa | 1 sourced value |
| Melting point | 1,865 to 1,910 °C | 2 sourced values across conditions |
| Electrical resistivity | 6.2e-7 to 6.8e-7 Ω·m | 1 sourced value |
What is the density of Platinum-tungsten and platinum-copper alloys?
Platinum-tungsten and platinum-copper alloys has a density of 21.3 g/cm³. The range covers 2 sourced values across the tempers, forms and test conditions the sources report; room-temperature values are used where a source states a temperature.
What is the melting point of Platinum-tungsten and platinum-copper alloys?
Platinum-tungsten and platinum-copper alloys has a melting point of 1,865 to 1,910 °C. The range covers 2 sourced values across the tempers, forms and test conditions the sources report; room-temperature values are used where a source states a temperature.
What is the yield strength of Platinum-tungsten and platinum-copper alloys?
Platinum-tungsten and platinum-copper alloys has a yield strength of 400 to 1,000 MPa. The source and test conditions are listed in the properties table on this page.
What is the tensile strength of Platinum-tungsten and platinum-copper alloys?
Platinum-tungsten and platinum-copper alloys has a tensile strength of 800 to 1,100 MPa. The source and test conditions are listed in the properties table on this page.
What is the Young's modulus of Platinum-tungsten and platinum-copper alloys?
Platinum-tungsten and platinum-copper alloys has a Young's modulus of 230 GPa. The source and test conditions are listed in the properties table on this page.
What are the other names and codes for Platinum-tungsten and platinum-copper alloys?
Platinum-tungsten and platinum-copper alloys is also written as PtW8, Hera 158. Each code is printed in the source listed beside it in the designations table.
What is Platinum-tungsten and platinum-copper alloys used for?
Uses recorded in the sources include Spark plug electrodes; Resistance and heater wire in high-temperature furnaces; Sensor assemblies, microfabricated probe tips and electrical feedthroughs.
Why it exists
Platinum-tungsten is chosen where a dense, heat-resistant precious metal is needed in wire form. Heraeus lists PtW8 for spark plug electrodes, resistance wire and medical wire, and Goodfellow lists the same composition for furnace heater wire, sensor assemblies and probe tips. Platinum-copper appears in the sources as a laboratory catalyst for acid fuel-cell reactions. The bulk alloy's properties are not in the sources read here.
Where it's used
Spark plug electrodes
Heraeus lists PtW8 for spark plug electrodes, supplied as wire.
Furnace and heater wire
Goodfellow lists Pt92/W8 for specialised resistance wiring in high-temperature furnaces and for precision heater coils.
Sensors and probe tips
Goodfellow lists Pt92/W8 for advanced sensor assemblies, microfabricated probe tips and high-vacuum electrical feedthroughs.
Fuel-cell catalyst (laboratory)
A 2021 study reports a peak methanol oxidation current of 1236 A/g(Pt) for dealloyed PtCu/C, against 350 A/g(Pt) for a commercial Pt/C reference, in 0.1 M HClO4 with methanol.
Recipe
Pt-8W: platinum with 8 % tungsten by mass (Pt92/W8). Pt-Cu: carbon-supported PtCux nanoparticles, x = 1.3 by XRF before activation
Pt-8W is a binary alloy of platinum and tungsten, 92 % platinum and 8 % tungsten by mass. The Heraeus datasheet calls the same grade PtW8 and gives no composition; the 8 % figure comes from the Goodfellow and Calfine product names. Platinum-copper has no fixed bulk composition in these sources. The catalyst studied has a Cu to Pt ratio of 1.3 by XRF before activation, and its lattice parameter gives a Vegard composition of PtCu0.54.
| Ingredient | Share of the weight | What it does |
|---|---|---|
| Platinum Pt | 92% | The matrix metal, about 92 % by mass. The Heraeus datasheet gives a density of 21.26 g/cm3 for the alloy. |
| Tungsten W | 8% | The minor element, about 8 % by mass. The datasheet gives tensile strength of 800 to 1100 MPa for the alloy, but does not say what tungsten contributes. |
Weight shares are as printed in the sources.
What it can do
Density
21.26 g/cm3
measured
The PtW8 wire has a density of 21.26 g/cm3 in the Heraeus datasheet. Goodfellow gives 21.3 g/cm3 for Pt92/W8.
Melting
1865 to 1885 °C
measured
Heraeus gives a melting range of 1865 to 1885 °C for PtW8. Goodfellow gives 1870 to 1910 °C for Pt92/W8.
Hardness
200 to 300 HV
measured
The Heraeus datasheet gives 200 to 300 HV for PtW8, with tensile strength of 800 to 1100 MPa.
Catalyst activity
1236 A/g(Pt)
measured
The dealloyed PtCu/C catalyst gave a peak methanol oxidation current of 1236 A/g(Pt), against 350 A/g(Pt) for the commercial reference, in one laboratory study.
How it compares
Platinum-tungsten is a heavy, high-melting wire metal with low electrical conductivity (2.58 to 2.77 % IACS in the Heraeus datasheet). The Heraeus datasheet gives its melting range as 1865 to 1885 °C. The rows below show the bulk alloy's density, melting range and modulus where a source gives them; no comparison with other materials was read in this run.
The same measurements for each material, so you can compare them. Each row names the key condition under the value; the full conditions and methods are in the numbered notes under Technical details. Other materials are shown beside it; each was measured under its own conditions, so open its page before comparing closely. Compare every grade in the family.
| Measurement | Pt-W, Pt-Cu | Au | Ag | Pt | Pd | Rh | Ru | Os | Au alloys | AuSn | Ag 92.5 Cu 7.5 | Ag alloys | Pd-Ag | Pd-Cu, Pd-Ni, Pd-Cr | Pt-Rh | Pt-Ir |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Thermal behavior and safety | ||||||||||||||||
| Melting range, PtW8 (Heraeus Hera 158)Range printed in a manufacturer datasheet | 1865 to 1885 °C | 1065 °C | 961.9 °C | 1769 °C | 1555 °C | 1964 °C | 2334 °C | 3033 °C | 955 °C | 280 °C | 788 to 891 °C | 780 °C | no data | 1397 °C | 1840 to 1870 °C | 1790 to 1800 °C |
| Melting range, Pt92/W8 (Goodfellow)Range printed on a reseller product page | 1870 to 1910 °C | 1065 °C | 961.9 °C | 1769 °C | 1555 °C | 1964 °C | 2334 °C | 3033 °C | 955 °C | 280 °C | 788 to 891 °C | 780 °C | no data | 1397 °C | 1840 to 1870 °C | 1790 to 1800 °C |
| Physical and electrical | ||||||||||||||||
| Density, PtW8 wire (Heraeus Hera 158)Value printed in a manufacturer datasheet | 21.26 g/cm³ | 19.3 g/cm³ | 10.5 g/cm³ | 21.45 g/cm³ | 12.02 g/cm³ | 12.42 g/cm³ | 12.36 g/cm³ | 22.5 g/cm³ | 15.8 g/cm³ | 14.7 - | 10.4 g/cm³ | 10 Mg/m3 | 10.9 g/cm³ | 10.8 g/cm³ | 19.97 g/cm³ | 21.54 g/cm³ |
| Density, Pt92/W8 wire (Goodfellow)Value printed on a reseller product page | 21.3 g/cm³ | 19.3 g/cm³ | 10.5 g/cm³ | 21.45 g/cm³ | 12.02 g/cm³ | 12.42 g/cm³ | 12.36 g/cm³ | 22.5 g/cm³ | 15.8 g/cm³ | 14.7 - | 10.4 g/cm³ | 10 Mg/m3 | 10.9 g/cm³ | 10.8 g/cm³ | 19.97 g/cm³ | 21.54 g/cm³ |
| Hardness HV, PtW8 (Heraeus Hera 158)Range printed in a manufacturer datasheet | 200 to 300 HV | no data | no data | 42 HV | 40 HV | no data | 750 kgf/mm2 | 300 to 350 kgf/mm2 | no data | no data | no data | no data | 55 HV | 580 to 620 HV | no data | 105 HV |
| Electrical conductivity range, PtW8 (Heraeus Hera 158) | 2.58 to 2.77 % IACS1 | 4.5×10^7 S/m | no data | 15.78 to 16.07 % IACS | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | 6.83 to 7.02 % IACS |
| Electrical resistivity, Pt92/W8 (Goodfellow)Range printed on a reseller product page | 62 to 68 µOhm cm | 2.2×10^-8 ohm m | 1.63 µΩ·cm | 10.6 µΩ·cm | 10.8 uOhm.cm | 43.3 nΩ·m | 71 nΩ·m | 8.8 µΩ·cm | 15.5 µΩ·cm | no data | 1.8 µOhmcm | 20.4 x10-9 ohm m | 15 uOhm.cm | no data | no data | no data |
| Temperature behavior | ||||||||||||||||
| Temperature coefficient of resistance, Pt92/W8 (Goodfellow)Value printed on a reseller product page | 2.5×10^-4 K-12 | no data | no data | 0.0039 /°C | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data |
| Other measurements | ||||||||||||||||
| Tensile strength, PtW8 (Heraeus Hera 158)Range printed in a manufacturer datasheet | 800 to 1100 MPa | no data | no data | 150 MPa | no data | no data | no data | no data | 616 MPa | 275 MPa | 207 MPa | 372 MPa | 310 MPa | no data | 300 to 680 MPa | 340 MPa |
| Yield strength, PtW8 (Heraeus Hera 158)Range printed in a manufacturer datasheet | 400 to 1000 MPa | no data | no data | 70 MPa | no data | no data | no data | no data | no data | no data | no data | 272 MPa | 150 MPa | no data | 180 to 670 MPa | 220 MPa |
| Elongation, PtW8 (Heraeus Hera 158)Range printed in a manufacturer datasheet | 2 to 20 % | no data | no data | 40 % | no data | no data | no data | no data | 13 % | no data | no data | 19 % | 36 % | 3 % | 1.5 to 32 % | 32 % |
| Modulus of elasticity, Pt92/W8 (Goodfellow)Value printed on a reseller product page | 230 GPa | no data | no data | 170 GPa | 121 GPa | 380 GPa | 447 GPa | 559 GPa | no data | 68 GPa | no data | 80 to 85 GPa | 114 GPa | no data | 208 GPa | 202.3 GPa |
| Electrochemically active surface area, PtCu/C activated 0.04 to 1.20 V | 41 m2/g(Pt)3 | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data |
| Electrochemically active surface area, PtCu/C activated 0.04 to 1.00 V | 43 m2/g(Pt)4 | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data |
| Peak methanol oxidation current, PtCu/C activated 0.04 to 1.00 V | 1236 A/g(Pt)5 | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data |
| Peak methanol oxidation current, commercial Pt/C reference (JM20) | 350 A/g(Pt)6 | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data |
| Lattice parameter a, PtCu/C from XRD | 3.815 Å7 | no data | no data | no data | 3.891 angstrom | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data |
| XRD crystallite size, PtCu/C (Scherrer) | 2.7 nm8 | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data | no data |
Why choose it, and why not
Good for
- Heat-resistant wire where density is acceptable. Heraeus lists PtW8 for resistance wire and spark plug electrodes.
- Sensor and probe wire. Goodfellow lists Pt92/W8 for sensor assemblies and microfabricated probe tips.
- Laboratory fuel-cell catalyst research on dealloyed PtCu/C, in acid electrolyte.
Watch out for
- Heavy for its size at 21.26 g/cm3.
- Low conductivity, 2.58 to 2.77 % IACS in the datasheet.
- The PtCu catalyst loses copper in acid during activation. The composition moves from PtCu1.3 to about PtCu0.25.
- No bulk Pt-Cu density, melting point or hardness was read in this run.
Platinum-tungsten is a dense, oxidation-resistant wire metal with datasheet values for density, melting range and mechanical strength. Platinum-copper is only covered here as a catalyst, and the bulk alloy needs a handbook source before it is used.
Technical details
For scientists and researchers. Everything above comes from the record below: every number with its method, its conditions and its source.
Other names and standards
The same grade under other systems, as datasheets and standards print them. Each code was checked against the page it comes from.
| System | Codes |
|---|---|
| Trade name | PtW8, Hera 158 |
Notes
The method, full conditions and any caveat for the numbered rows above.
| # | Measurement | Method | Conditions | Caveat |
|---|---|---|---|---|
| 1 | Electrical conductivity range, PtW8 (Heraeus Hera 158) | Minimum and maximum printed in a manufacturer datasheet. The datasheet prints the minimum (2.77) above the maximum (2.58), so the range is entered low to high. Check the datasheet before using either end. | form PtW8 wiretemperature not stated in the datasheet | — |
| 2 | Temperature coefficient of resistance, Pt92/W8 (Goodfellow) | — | form Pt92/W8 wiretemperature range not stated on the page | Non-canonical name; add to property-canon if kept. |
| 3 | Electrochemically active surface area, PtCu/C activated 0.04 to 1.20 V | Value printed in a 2021 open-access paper, Table 1 | form carbon-supported PtCu/C catalyst, nominal PtCu1.3 before activationelectrolyte 0.1 M HClO4activation 100 voltammetric cycles, 0.04 to 1.20 V vs RHE, 200 mV/s | Non-canonical name. |
| 4 | Electrochemically active surface area, PtCu/C activated 0.04 to 1.00 V | Value printed in a 2021 open-access paper, Table 1 | form carbon-supported PtCu/C catalyst, nominal PtCu1.3 before activationelectrolyte 0.1 M HClO4activation 100 voltammetric cycles, 0.04 to 1.00 V vs RHE, 200 mV/s | Non-canonical name. |
| 5 | Peak methanol oxidation current, PtCu/C activated 0.04 to 1.00 V | Value printed in a 2021 open-access paper, Table 2 | electrolyte 0.1 M HClO4 with 0.5 M CH3OH, argonscan 20 mV/s, 0.04 to 1.3 V vs RHE | Non-canonical name. Normalised to platinum mass by the authors. |
| 6 | Peak methanol oxidation current, commercial Pt/C reference (JM20) | Value printed in a 2021 open-access paper, Table 2 | electrolyte 0.1 M HClO4 with 0.5 M CH3OH, argonscan 20 mV/s, 0.04 to 1.3 V vs RHE | Non-canonical name. Reference catalyst for the comparison above. |
| 7 | Lattice parameter a, PtCu/C from XRD | Value calculated and printed in a 2021 open-access paper | form PtCu/C catalyst, Pt-Cu solid solutionmethod XRD with Vegard's law | Non-canonical name. The same sentence gives the composition PtCu0.54 by Vegard's law. |
| 8 | XRD crystallite size, PtCu/C (Scherrer) | Value printed in a 2021 open-access paper; plus or minus 0.1 nm printed | form PtCu/C catalystmethod Scherrer equation from XRD | Non-canonical name. TEM gives a nanoparticle size of about 5 nm, which the authors say is larger than the XRD crystallite size. |
Corrosion and compatibility
What happens when it meets other materials and environments.
| Environment | Concern | What happens |
|---|---|---|
| Air at high temperature (PtW8 wire) | low | Heraeus lists PtW8 as oxidation resistant to 1000 °C.1 |
| Acid electrolyte with electrochemical cycling (PtCu/C catalyst) | moderate | Copper leaves the PtCu/C surface during activation in acid, and the copper content falls.2 |
| # | Environment | Details | Test conditions |
|---|---|---|---|
| 1 | Air at high temperature (PtW8 wire) | The datasheet gives this as a chemical-property comment with no test method, atmosphere, exposure time or oxidation rate. | basis qualitative datasheet statement onlylimit 1000 °C as printed |
| 2 | Acid electrolyte with electrochemical cycling (PtCu/C catalyst) | After 100 voltammetric cycles in 0.1 M HClO4, the Cu to Pt ratio fell from PtCu1.3 to PtCu0.25 after activation to 1.20 V, and to PtCu0.24 after activation to 1.00 V. The authors call this de-alloying. The text read here does not report Pt or Cu dissolved into the electrolyte. | electrolyte 0.1 M HClO4cycling 100 cycles at 200 mV/s, 0.04 to 1.20 V or 0.04 to 1.00 V vs RHEcomposition basis after the activation stage, as printed in Table 1 |
Risks and side effects
Hazards to people, what happens when a cell overheats, and how the material is handled and stored.
For people
The platinum, tungsten and copper element records carry flammable, irritant or aquatic codes in some company reports. The alloys have no record of their own.
- Platinum element
- Of 504 company reports, 410 said platinum does not meet GHS criteria. H228 (flammable solid, 10.7 %) is shown, and H334 (respiratory sensitisation) comes from the notifications.
- Tungsten element
- Of 741 company reports, 196 said tungsten does not meet GHS criteria. H228 (73.4 %) and H252 (47.8 %, self-heating in large quantities) are shown, with H320 and H335.
- Copper element
- Of 3463 company reports, 1818 said copper does not meet GHS criteria. Notified codes include H400 (43.1 %) and H410 (18.8 %), which concern aquatic life, and H302 (21.7 %).
If it fails
The only failure route in a read source is copper loss from the catalyst in acid, found in a laboratory study.
- Catalyst activation
- In the 2021 study, 100 cycles in 0.1 M HClO4 took the Cu to Pt ratio from 1.3 to about 0.25. The two activation windows gave the same composition but different kinetic currents, so the surface state matters as well as the composition.
Handling and storage
- Forming
- Heraeus lists PtW8 as ductile and formable, but hardly formable, and as not age hardenable. It is machinable.
- Heat
- The datasheet lists oxidation resistance to 1000 °C. It gives no test conditions.
Test details
The original wording and numbers from the sources, for readers who want them.
Failure risks
| Failure | Trigger and consequence |
|---|---|
| Copper loss from the PtCu catalyst surface in acidmoderate severity | Electrochemical activation cycling in 0.1 M HClO4Copper falls to a Cu to Pt ratio of about 0.25 after activation in both windows, while the activation window changes the kinetic current (417 and 878 A/g(Pt) in Table 1). The authors attribute the activity difference to surface structure, not composition. |
Side effects on surrounding parts
| Affects | Effect |
|---|---|
| Mass of electrodes, probes and wire assemblies | PtW8 density is 21.26 g/cm3, so parts are heavy for their size. |
Handling and storage
- Heraeus lists PtW8 as ductile, formable and machinable, but hardly formable, and as not age hardenable.
Supply and geography
How common the raw materials are and where they come from.
Platinum (world mine production, used for the platinum content)
- Top producers (2025)
- South Africa 70.6%, Russia 11.8%, Zimbabwe 10.6%, Canada 2.9%, United States 1.1%
- Recycling
- USGS: about 140,000 kg of palladium and platinum were recovered globally from new and old scrap in 2025.
Tungsten
- Top producers (2025)
- China 78.8%, Vietnam 3.5%, Kazakhstan 2.8%, Russia 2.4%, Korea, North 2.4%
- Recycling
- USGS: the quantity of secondary tungsten produced and consumed in 2025 was withheld to avoid disclosing company data.
- Substitutes
- USGS: molybdenum can replace tungsten in some mill products, and depleted uranium or lead can replace tungsten alloys where high density or radiation shielding is needed.
Copper
- Top producers (2025)
- Chile 23%, Congo (Kinshasa) 13.9%, Peru 11.7%, China 7.8%, Russia 5.7%
- Critical mineral lists
- US: listed
- Recycling
- USGS: old scrap gave an estimated 160,000 tons of copper in the United States in 2025.
- Substitutes
- USGS: aluminum substitutes for copper in several electrical and cooling uses, and optical fiber substitutes for copper in telecommunications.
Documents
Datasheets, safety data sheets, papers and standards you can open.
Full record
The complete spore, as stored. Free to reuse under CC-BY-4.0. Images keep the licence shown with each one.
Show the full YAML
spore: profile
id: platinum-tungsten-copper
spore_version: 0.2
family: precious-metals
name: Platinum-tungsten and platinum-copper alloys
abbreviation: Pt-W, Pt-Cu
role: resistance wire, probes and spark-plug electrodes (Pt-W); catalysts (Pt-Cu)
category: metals
type: precious-metals
summary: |
Platinum-tungsten is a ductile precious-metal alloy. The grade read here is Pt-8W, 92 % platinum and 8 % tungsten by mass, sold by Heraeus as PtW8 (Hera 158) and by Goodfellow as Pt92/W8 wire. The Heraeus datasheet gives a density of 21.26 g/cm3 and a melting range of 1865 to 1885 °C, and lists PtW8 for spark plug electrodes, resistance wire and medical wire. Goodfellow lists the same composition for high-temperature furnace wiring, precision heater coils and sensor assemblies. Platinum-copper appears in the sources read here as a catalyst: a 2021 open-access study of carbon-supported PtCu nanoparticles reports a lattice parameter of 3.815 Å and a peak methanol-oxidation current of 1236 A/g(Pt). No bulk density, melting point or hardness for Pt-Cu was read in this run.
best_for: Fine resistance wire, probes and electrodes that must resist oxidation in air at high temperature (Pt-W), and dealloyed PtCu catalysts in acid electrolyte (Pt-Cu, laboratory).
weakest_at: Density (21.26 g/cm3) and conductivity (2.58 to 2.77 % IACS, a poor conductor). The PtCu catalyst loses much of its copper in acid.
identity:
formula: 'Pt-8W: platinum with 8 % tungsten by mass (Pt92/W8). Pt-Cu: carbon-supported PtCux nanoparticles, x = 1.3 by XRF before activation'
source: goodfellow-ptw
where: Composition line, Pt 92/W 8 (Goodfellow). Heraeus designation PtW8 on the datasheet title line.
designations:
- system: Trade name
code: PtW8
source: hera158
where: Title line, product name
- system: Trade name
code: Hera 158
source: hera158
where: Title line, product name
tags:
environments: []
stresses: []
applications:
- propulsion-and-tanks
- thermal-control
- electronics-and-chips
- batteries
properties:
- benchmark: density
label: Density, PtW8 wire (Heraeus Hera 158)
value: 21.26
unit: g/cm3
scope: material
conditions:
form: PtW8 wire
temperature: not stated in the datasheet
method: Value printed in a manufacturer datasheet
status: ground
source: hera158
where: General information table, row Density, g/cm3
- benchmark: density
label: Density, Pt92/W8 wire (Goodfellow)
value: 21.3
unit: g/cm3
scope: material
conditions:
form: Pt92/W8 spooled wire
temperature: not stated on the page
method: Value printed on a reseller product page
status: ground
source: goodfellow-ptw
where: Physical properties list, Density
- benchmark: melting_point
label: Melting range, PtW8 (Heraeus Hera 158)
value: 1865
value_high: 1885
bound: range
unit: °C
scope: material
conditions:
form: PtW8 wire
pressure: not stated
method: Range printed in a manufacturer datasheet
status: ground
source: hera158
where: General information table, row Melting Range, °C
- benchmark: melting_point
label: Melting range, Pt92/W8 (Goodfellow)
value: 1870
value_high: 1910
bound: range
unit: °C
scope: material
conditions:
form: Pt92/W8 wire
pressure: not stated
method: Range printed on a reseller product page
status: ground
source: goodfellow-ptw
where: Physical properties list, Melting point
- benchmark: vickers_hardness
label: Hardness HV, PtW8 (Heraeus Hera 158)
value: 200
value_high: 300
bound: range
unit: HV
scope: material
conditions:
form: PtW8 wire
temper: not stated; the datasheet gives one property range
method: Range printed in a manufacturer datasheet
status: ground
source: hera158
where: Property Range table, row Hardness HV
- benchmark: ultimate_tensile_strength
label: Tensile strength, PtW8 (Heraeus Hera 158)
value: 800
value_high: 1100
bound: range
unit: MPa
scope: material
conditions:
form: PtW8 wire
temper: not stated; one property range printed
method: Range printed in a manufacturer datasheet
status: ground
source: hera158
where: Property Range table, row Tensile Strength MPa
- benchmark: yield_strength
label: Yield strength, PtW8 (Heraeus Hera 158)
value: 400
value_high: 1000
bound: range
unit: MPa
scope: material
conditions:
form: PtW8 wire
temper: not stated; one property range printed
method: Range printed in a manufacturer datasheet
status: ground
source: hera158
where: Property Range table, row Yield Strength MPa
- benchmark: elongation
label: Elongation, PtW8 (Heraeus Hera 158)
value: 2
value_high: 20
bound: range
unit: '%'
scope: material
conditions:
form: PtW8 wire
gauge_length: not stated
method: Range printed in a manufacturer datasheet
status: ground
source: hera158
where: Property Range table, row Elongation %
- benchmark: electrical_conductivity
label: Electrical conductivity range, PtW8 (Heraeus Hera 158)
value: 2.58
value_high: 2.77
bound: range
unit: '% IACS'
scope: material
conditions:
form: PtW8 wire
temperature: not stated in the datasheet
method: Minimum and maximum printed in a manufacturer datasheet. The datasheet prints the minimum (2.77) above the maximum (2.58), so the range is entered low to high. Check the datasheet before using either end.
status: ground
source: hera158
where: Physical properties table, rows Conductivity min % IACS and Conductivity max % IACS
- benchmark: electrical_resistivity
label: Electrical resistivity, Pt92/W8 (Goodfellow)
value: 62
value_high: 68
bound: range
unit: µOhm cm
scope: material
conditions:
form: Pt92/W8 wire
temperature: not stated on the page
method: Range printed on a reseller product page
status: ground
source: goodfellow-ptw
where: Physical properties list, Electrical resistivity
- benchmark: elastic_modulus
label: Modulus of elasticity, Pt92/W8 (Goodfellow)
value: 230
unit: GPa
scope: material
conditions:
form: Pt92/W8 wire
temperature: not stated on the page
method: Value printed on a reseller product page
status: ground
source: goodfellow-ptw
where: Physical properties list, Modulus of elasticity
- benchmark: temperature_coefficient_of_resistance
label: Temperature coefficient of resistance, Pt92/W8 (Goodfellow)
value: 0.00025
unit: K-1
scope: material
conditions:
form: Pt92/W8 wire
temperature_range: not stated on the page
method: Value printed on a reseller product page
status: ground
note: Non-canonical name; add to property-canon if kept.
source: goodfellow-ptw
where: Physical properties list, Temperature coefficient
- benchmark: electrochemically_active_surface_area
label: Electrochemically active surface area, PtCu/C activated 0.04 to 1.20 V
value: 41
unit: m2/g(Pt)
scope: material
conditions:
form: carbon-supported PtCu/C catalyst, nominal PtCu1.3 before activation
electrolyte: 0.1 M HClO4
activation: 100 voltammetric cycles, 0.04 to 1.20 V vs RHE, 200 mV/s
method: Value printed in a 2021 open-access paper, Table 1
status: ground
note: Non-canonical name.
source: pavlets2021
where: Table 1, row PtCu/C with activation range 0.04 to 1.20 V, column ESA
- benchmark: electrochemically_active_surface_area
label: Electrochemically active surface area, PtCu/C activated 0.04 to 1.00 V
value: 43
unit: m2/g(Pt)
scope: material
conditions:
form: carbon-supported PtCu/C catalyst, nominal PtCu1.3 before activation
electrolyte: 0.1 M HClO4
activation: 100 voltammetric cycles, 0.04 to 1.00 V vs RHE, 200 mV/s
method: Value printed in a 2021 open-access paper, Table 1
status: ground
note: Non-canonical name.
source: pavlets2021
where: Table 1, row PtCu/C with activation range 0.04 to 1.00 V, column ESA
- benchmark: methanol_oxidation_peak_current
label: Peak methanol oxidation current, PtCu/C activated 0.04 to 1.00 V
value: 1236
unit: A/g(Pt)
scope: material
conditions:
electrolyte: 0.1 M HClO4 with 0.5 M CH3OH, argon
scan: 20 mV/s, 0.04 to 1.3 V vs RHE
method: Value printed in a 2021 open-access paper, Table 2
status: ground
note: Non-canonical name. Normalised to platinum mass by the authors.
source: pavlets2021
where: Table 2, row PtCu/C 0.04 to 1.00 V, column Imax
- benchmark: methanol_oxidation_peak_current
label: Peak methanol oxidation current, commercial Pt/C reference (JM20)
value: 350
unit: A/g(Pt)
scope: material
conditions:
electrolyte: 0.1 M HClO4 with 0.5 M CH3OH, argon
scan: 20 mV/s, 0.04 to 1.3 V vs RHE
method: Value printed in a 2021 open-access paper, Table 2
status: ground
note: Non-canonical name. Reference catalyst for the comparison above.
source: pavlets2021
where: Table 2, row JM20 0.04 to 1.20 V, column Imax
- benchmark: lattice_parameter
label: Lattice parameter a, PtCu/C from XRD
value: 3.815
unit: Å
scope: material
conditions:
form: PtCu/C catalyst, Pt-Cu solid solution
method: XRD with Vegard's law
method: Value calculated and printed in a 2021 open-access paper
status: ground
note: Non-canonical name. The same sentence gives the composition PtCu0.54 by Vegard's law.
source: pavlets2021
where: Section 2 (XRD results), sentence beginning For the obtained PtCu/C catalyst
- benchmark: crystallite_size
label: XRD crystallite size, PtCu/C (Scherrer)
value: 2.7
unit: nm
scope: material
conditions:
form: PtCu/C catalyst
method: Scherrer equation from XRD
method: Value printed in a 2021 open-access paper; plus or minus 0.1 nm printed
status: ground
note: Non-canonical name. TEM gives a nanoparticle size of about 5 nm, which the authors say is larger than the XRD crystallite size.
source: pavlets2021
where: Section 2 (XRD results), sentence with the Scherrer calculation
corrosion:
- environment: Air at high temperature (PtW8 wire)
headline: Heraeus lists PtW8 as oxidation resistant to 1000 °C.
effect: The datasheet gives this as a chemical-property comment with no test method, atmosphere, exposure time or oxidation rate.
rating: low
conditions:
basis: qualitative datasheet statement only
limit: 1000 °C as printed
source: hera158
where: Chemical Properties section, Comment row
- environment: Acid electrolyte with electrochemical cycling (PtCu/C catalyst)
headline: Copper leaves the PtCu/C surface during activation in acid, and the copper content falls.
effect: After 100 voltammetric cycles in 0.1 M HClO4, the Cu to Pt ratio fell from PtCu1.3 to PtCu0.25 after activation to 1.20 V, and to PtCu0.24 after activation to 1.00 V. The authors call this de-alloying. The text read here does not report Pt or Cu dissolved into the electrolyte.
rating: moderate
conditions:
electrolyte: 0.1 M HClO4
cycling: 100 cycles at 200 mV/s, 0.04 to 1.20 V or 0.04 to 1.00 V vs RHE
composition_basis: after the activation stage, as printed in Table 1
source: pavlets2021
where: Section 2 (activation procedure) and Table 1, column Composition after the Activation Stage
risks:
hazards:
- text: 'PubChem tungsten record (CID 23964): 26.5 % of company reports (196 of 741) do not meet GHS criteria. Notified codes are H228 (73.4 %, flammable solid), H252 (47.8 %, self-heating in large quantities), H320 (eye irritation) and H335 (respiratory irritation).'
ghs:
- H228
- H252
- H320
- H335
source: pubchem-w
where: Safety and Hazards, GHS Classification (CID 23964)
- text: 'PubChem platinum record (CID 23939): 81.3 % of company reports (410 of 504) do not meet GHS criteria. H228 (10.7 %, flammable solid) is shown, and H315 (skin irritation) and H334 (sensitisation, respiratory) come from the notifications.'
ghs:
- H228
- H315
- H334
source: pubchem-pt
where: Safety and Hazards, GHS Classification (CID 23939)
- text: 'PubChem copper record (CID 23978): 52.5 % of company reports (1818 of 3463) do not meet GHS criteria. Notified codes include H302 (21.7 %), H400 (43.1 %), H410 (18.8 %), H411 (22.5 %), H317, H335, H370 and H372.'
ghs:
- H302
- H317
- H335
- H370
- H372
- H400
- H410
- H411
source: pubchem-cu
where: Safety and Hazards, GHS Classification (CID 23978)
failure_risks:
- mode: Copper loss from the PtCu catalyst surface in acid
trigger: Electrochemical activation cycling in 0.1 M HClO4
consequence: Copper falls to a Cu to Pt ratio of about 0.25 after activation in both windows, while the activation window changes the kinetic current (417 and 878 A/g(Pt) in Table 1). The authors attribute the activity difference to surface structure, not composition.
severity: moderate
source: pavlets2021
where: Table 1, columns Composition after the Activation Stage and Ik A g-1 (Pt); Section 2
side_effects:
- text: PtW8 density is 21.26 g/cm3, so parts are heavy for their size.
affects: Mass of electrodes, probes and wire assemblies
source: hera158
where: General information table, row Density
handling:
- text: Heraeus lists PtW8 as ductile, formable and machinable, but hardly formable, and as not age hardenable.
source: hera158
where: Forming Processes table, rows Age Hardenable, Material Behaviour and Forming Process
mitigations: []
uses:
- application: propulsion-and-tanks
device: Spark plug electrodes
example: Heraeus lists PtW8 for spark plug electrodes, supplied as wire.
source: hera158
where: General information table, row Applications
- application: thermal-control
device: Resistance and heater wire in high-temperature furnaces
example: Goodfellow lists Pt92/W8 wire for specialised resistance wiring in high-temperature furnaces and for precision heater coils.
source: goodfellow-ptw
where: Uses and applications description
- application: electronics-and-chips
device: Sensor assemblies, microfabricated probe tips and electrical feedthroughs
example: Goodfellow lists Pt92/W8 for advanced sensor assemblies, microfabricated probe tips and high-vacuum electrical feedthroughs.
source: goodfellow-ptw
where: Uses and applications description
- application: batteries
device: Acid fuel-cell electrode catalyst (laboratory study, not a battery)
example: A 2021 study reports a peak methanol oxidation current of 1236 A/g(Pt) for dealloyed PtCu/C, against 350 A/g(Pt) for a commercial Pt/C reference, in 0.1 M HClO4 with methanol.
source: pavlets2021
where: Introduction and Table 2
supply:
- subject: Platinum (world mine production, used for the platinum content)
producers:
- country: South Africa
share_percent: 70.6
year: 2025
- country: Russia
share_percent: 11.8
year: 2025
- country: Zimbabwe
share_percent: 10.6
year: 2025
- country: Canada
share_percent: 2.9
year: 2025
- country: United States
share_percent: 1.1
year: 2025
critical_lists: []
recycling: 'USGS: about 140,000 kg of palladium and platinum were recovered globally from new and old scrap in 2025.'
substitutes: []
source: usgs-mcs2026-pgm
where: World Mine Production and Reserves table, platinum 2025e (South Africa 120,000 kg, Russia 20,000, Zimbabwe 18,000, Canada 5,000, United States 1,800, world total 170,000 kg). Shares calculated by Space Mushroom from those kilogram values. Recycling paragraph, PGM chapter.
- subject: Tungsten
producers:
- country: China
share_percent: 78.8
year: 2025
- country: Vietnam
share_percent: 3.5
year: 2025
- country: Kazakhstan
share_percent: 2.8
year: 2025
- country: Russia
share_percent: 2.4
year: 2025
- country: Korea, North
share_percent: 2.4
year: 2025
critical_lists: []
recycling: 'USGS: the quantity of secondary tungsten produced and consumed in 2025 was withheld to avoid disclosing company data.'
substitutes:
- 'USGS: molybdenum can replace tungsten in some mill products, and depleted uranium or lead can replace tungsten alloys where high density or radiation shielding is needed.'
source: usgs-mcs2026-tungsten
where: World Mine Production table, mine production 2025e (China 67,000 t, Kazakhstan 2,400, Vietnam 3,000, Russia 2,000, Korea North 2,000, world total 85,000 t of tungsten content). Shares calculated by Space Mushroom. Recycling and Substitutes paragraphs.
- subject: Copper
producers:
- country: Chile
share_percent: 23
year: 2025
- country: Congo (Kinshasa)
share_percent: 13.9
year: 2025
- country: Peru
share_percent: 11.7
year: 2025
- country: China
share_percent: 7.8
year: 2025
- country: Russia
share_percent: 5.7
year: 2025
critical_lists:
- list: USGS Final 2025 List of Critical Minerals (the copper chapter says copper was added in 2025)
listed: true
recycling: 'USGS: old scrap gave an estimated 160,000 tons of copper in the United States in 2025.'
substitutes:
- 'USGS: aluminum substitutes for copper in several electrical and cooling uses, and optical fiber substitutes for copper in telecommunications.'
source: usgs-mcs2026-copper
where: World Mine and Refinery Production table, mine production 2025e (world total 23,000 thousand t of copper content; Chile 5,300; Congo (Kinshasa) 3,200; Peru 2,700; China 1,800; Russia 1,300). Shares calculated by Space Mushroom. Critical list statement and Recycling and Substitutes paragraphs.
documents:
- title: Heraeus Precious Metals, PtW8 (Hera 158) datasheet, status 11/2021
type: datasheet
url: https://pim.heraeus.com/datasheets/HPM/FM/Contact%20Materials/Hera_158_Datasheet_EN_(Heraeus_Precious_Metals).pdf
year: 2021
- title: Goodfellow, Platinum/Tungsten Alloy Spooled Wire (Pt92/W8) product page
type: datasheet
url: https://www.goodfellow.com/usa/platinum-tungsten-alloy-spooled-wire-pt92-w8-group
year: 2026
- title: PubChem compound record, Tungsten (CID 23964), GHS classification
type: database
url: https://pubchem.ncbi.nlm.nih.gov/compound/23964
year: 2026
- title: PubChem compound record, Platinum (CID 23939), GHS classification
type: database
url: https://pubchem.ncbi.nlm.nih.gov/compound/23939
year: 2026
- title: PubChem compound record, Copper (CID 23978), GHS classification
type: database
url: https://pubchem.ncbi.nlm.nih.gov/compound/23978
year: 2026
- title: Mineral Commodity Summaries 2026, full report (platinum-group metals chapter)
type: report
url: https://pubs.usgs.gov/periodicals/mcs2026/mcs2026.pdf
year: 2026
- title: Mineral Commodity Summaries 2026, Tungsten
type: report
url: https://pubs.usgs.gov/periodicals/mcs2026/mcs2026-tungsten.pdf
year: 2026
- title: Mineral Commodity Summaries 2026, Copper
type: report
url: https://pubs.usgs.gov/periodicals/mcs2026/mcs2026-copper.pdf
year: 2026
- title: Pavlets et al., Influence of Electrochemical Pretreatment Conditions of PtCu/C Alloy Electrocatalyst on Its Activity, Nanomaterials 11, 1499 (open access)
type: paper
url: https://pmc.ncbi.nlm.nih.gov/articles/PMC8229528/
year: 2021
gaps:
- No bulk density, melting range or hardness for Pt-Cu was read in a page this run. The 2014 PtCu3 ordering paper (RSC Phys. Chem. Chem. Phys.) and the 2021 Nanoscale de-alloyed PtCu/C paper returned HTTP 403, so their numbers are not used.
- No Pt-Cu datasheet, handbook or phase-diagram page was read. ASM Handbook and Hansen or Massalski phase-diagram sources were not reached in this run.
- No Young's modulus, thermal conductivity, expansion coefficient or specific heat for PtW8 appears in the Heraeus datasheet, and no other page read gives them with a condition.
- The Heraeus datasheet gives no temperature or test method for any PtW8 property. Goodfellow gives no test conditions for its values.
- The 8 % tungsten composition is from the Goodfellow product name (Pt92/W8) and the Calfine product name (Platinum 8% Tungsten), not from the Heraeus datasheet, which prints no composition.
- No UNS, EN, DIN, JIS or ASTM designation for PtW8 was printed in a page read this run. Only the Heraeus names PtW8 and Hera 158 are recorded.
- The Calfine Pt-8W page gives a thermal EMF against copper of -0.014 with no unit or temperature, and a resistivity printed with a mixed unit. Neither is used.
- No critical-mineral status for platinum or tungsten was confirmed from the chapters read in this run. Copper is recorded as listed, from its own chapter.
- Hazard records are for the platinum, tungsten and copper elements, not for the alloys. No Pt-W or Pt-Cu safety data sheet was read.
- Pt-Cu supply and corrosion entries describe the metals or the laboratory catalyst, not the bulk alloy. No bulk Pt-Cu corrosion or service test was found.
- The fuel-cell catalyst use has no fixed application in the list. It is filed under batteries and labelled as a laboratory fuel-cell catalyst, not a battery.
- Non-canonical benchmark names are used for vickers_hardness, electrical_conductivity, temperature_coefficient_of_resistance, electrochemically_active_surface_area, methanol_oxidation_peak_current, lattice_parameter and crystallite_size. Add them to spores/property-canon.yaml if they are kept.
- The Heraeus conductivity minimum and maximum are printed in reverse order (2.77 above 2.58). The range is entered low to high with a note in the method field.
- No space-electrode, vacuum outgassing or flight source for Pt-W or Pt-Cu was found in this run.
- Medical wire is listed for PtW8 in the datasheet and is mentioned in the story only. No fixed application in the list fits medical implants.
sources:
hera158:
title: Hera 158, PtW8, Heraeus Precious Metals datasheet (status 11/2021)
url: https://pim.heraeus.com/datasheets/HPM/FM/Contact%20Materials/Hera_158_Datasheet_EN_(Heraeus_Precious_Metals).pdf
year: 2021
kind: datasheet
license: Manufacturer datasheet (cited, not reproduced)
goodfellow-ptw:
title: Goodfellow, Platinum/Tungsten Alloy Spooled Wire (Pt92/W8) product page
url: https://www.goodfellow.com/usa/platinum-tungsten-alloy-spooled-wire-pt92-w8-group
year: 2026
kind: web
license: Supplier product page (cited, not reproduced)
pubchem-w:
title: PubChem compound record, Tungsten (CID 23964), GHS classification
id: CID 23964
url: https://pubchem.ncbi.nlm.nih.gov/compound/23964
year: 2026
kind: database
license: PubChem (NCBI); sections attributed to ECHA and NITE-CMC
pubchem-pt:
title: PubChem compound record, Platinum (CID 23939), GHS classification
id: CID 23939
url: https://pubchem.ncbi.nlm.nih.gov/compound/23939
year: 2026
kind: database
license: PubChem (NCBI); sections attributed to ECHA and NITE-CMC
pubchem-cu:
title: PubChem compound record, Copper (CID 23978), GHS classification
id: CID 23978
url: https://pubchem.ncbi.nlm.nih.gov/compound/23978
year: 2026
kind: database
license: PubChem (NCBI); sections attributed to ECHA and others
usgs-mcs2026-pgm:
title: Mineral Commodity Summaries 2026, Platinum-Group Metals chapter (U.S. Geological Survey, February 2026)
url: https://pubs.usgs.gov/periodicals/mcs2026/mcs2026.pdf
year: 2026
kind: report
license: public domain (USGS)
usgs-mcs2026-tungsten:
title: Mineral Commodity Summaries 2026, Tungsten (U.S. Geological Survey, February 2026)
url: https://pubs.usgs.gov/periodicals/mcs2026/mcs2026-tungsten.pdf
year: 2026
kind: report
license: public domain (USGS)
usgs-mcs2026-copper:
title: Mineral Commodity Summaries 2026, Copper (U.S. Geological Survey, February 2026)
url: https://pubs.usgs.gov/periodicals/mcs2026/mcs2026-copper.pdf
year: 2026
kind: report
license: public domain (USGS)
pavlets2021:
title: Influence of Electrochemical Pretreatment Conditions of PtCu/C Alloy Electrocatalyst on Its Activity (Nanomaterials 11, 1499)
id: doi:10.3390/nano11061499 (PMC8229528)
url: https://pmc.ncbi.nlm.nih.gov/articles/PMC8229528/
year: 2021
kind: paper
license: CC BY 4.0
license: CC-BY-4.0
updated: '2026-10-26'
review:
status: draft
method: assistant
checked_values: 18
unreachable: 2
caveats: 5
note: 'Read by an AI assistant on 2026-10-26 from the Heraeus Hera 158 datasheet, the Goodfellow Pt92/W8 page, PubChem records for W, Pt and Cu, the USGS MCS 2026 chapters for platinum, tungsten and copper, and one 2021 open-access paper on PtCu/C. Unreachable: two RSC articles on Pt-Cu (403). Caveats: the datasheets give no temperatures; the Pt-Cu values are for a carbon-supported catalyst, not bulk alloy; the platinum and tungsten shares and the copper shares are calculated from production values; the hazard records are for the elements; no bulk Pt-Cu property was found.'
story:
recipe:
line: Pt-8W is a binary alloy of platinum and tungsten, 92 % platinum and 8 % tungsten by mass. The Heraeus datasheet calls the same grade PtW8 and gives no composition; the 8 % figure comes from the Goodfellow and Calfine product names. Platinum-copper has no fixed bulk composition in these sources. The catalyst studied has a Cu to Pt ratio of 1.3 by XRF before activation, and its lattice parameter gives a Vegard composition of PtCu0.54.
parts:
- name: Platinum
symbol: Pt
share_percent: 92
role: The matrix metal, about 92 % by mass. The Heraeus datasheet gives a density of 21.26 g/cm3 for the alloy.
- name: Tungsten
symbol: W
share_percent: 8
role: The minor element, about 8 % by mass. The datasheet gives tensile strength of 800 to 1100 MPa for the alloy, but does not say what tungsten contributes.
risk_groups:
- title: For people
level: 1
verdict: Mixed element records
lead: The platinum, tungsten and copper element records carry flammable, irritant or aquatic codes in some company reports. The alloys have no record of their own.
points:
- label: Platinum element
line: Of 504 company reports, 410 said platinum does not meet GHS criteria. H228 (flammable solid, 10.7 %) is shown, and H334 (respiratory sensitisation) comes from the notifications.
- label: Tungsten element
line: Of 741 company reports, 196 said tungsten does not meet GHS criteria. H228 (73.4 %) and H252 (47.8 %, self-heating in large quantities) are shown, with H320 and H335.
- label: Copper element
line: Of 3463 company reports, 1818 said copper does not meet GHS criteria. Notified codes include H400 (43.1 %) and H410 (18.8 %), which concern aquatic life, and H302 (21.7 %).
- title: If it fails
lead: The only failure route in a read source is copper loss from the catalyst in acid, found in a laboratory study.
points:
- label: Catalyst activation
line: In the 2021 study, 100 cycles in 0.1 M HClO4 took the Cu to Pt ratio from 1.3 to about 0.25. The two activation windows gave the same composition but different kinetic currents, so the surface state matters as well as the composition.
- title: Handling and storage
points:
- label: Forming
line: Heraeus lists PtW8 as ductile and formable, but hardly formable, and as not age hardenable. It is machinable.
- label: Heat
line: The datasheet lists oxidation resistance to 1000 °C. It gives no test conditions.
why: Platinum-tungsten is chosen where a dense, heat-resistant precious metal is needed in wire form. Heraeus lists PtW8 for spark plug electrodes, resistance wire and medical wire, and Goodfellow lists the same composition for furnace heater wire, sensor assemblies and probe tips. Platinum-copper appears in the sources as a laboratory catalyst for acid fuel-cell reactions. The bulk alloy's properties are not in the sources read here.
uses:
- where: Spark plug electrodes
line: Heraeus lists PtW8 for spark plug electrodes, supplied as wire.
- where: Furnace and heater wire
line: Goodfellow lists Pt92/W8 for specialised resistance wiring in high-temperature furnaces and for precision heater coils.
- where: Sensors and probe tips
line: Goodfellow lists Pt92/W8 for advanced sensor assemblies, microfabricated probe tips and high-vacuum electrical feedthroughs.
- where: Fuel-cell catalyst (laboratory)
line: A 2021 study reports a peak methanol oxidation current of 1236 A/g(Pt) for dealloyed PtCu/C, against 350 A/g(Pt) for a commercial Pt/C reference, in 0.1 M HClO4 with methanol.
can_do:
- label: Density
value: 21.26 g/cm3
benchmark: density
line: The PtW8 wire has a density of 21.26 g/cm3 in the Heraeus datasheet. Goodfellow gives 21.3 g/cm3 for Pt92/W8.
- label: Melting
value: 1865 to 1885 °C
benchmark: melting_point
line: Heraeus gives a melting range of 1865 to 1885 °C for PtW8. Goodfellow gives 1870 to 1910 °C for Pt92/W8.
- label: Hardness
value: 200 to 300 HV
benchmark: vickers_hardness
line: The Heraeus datasheet gives 200 to 300 HV for PtW8, with tensile strength of 800 to 1100 MPa.
- label: Catalyst activity
value: 1236 A/g(Pt)
benchmark: methanol_oxidation_peak_current
line: The dealloyed PtCu/C catalyst gave a peak methanol oxidation current of 1236 A/g(Pt), against 350 A/g(Pt) for the commercial reference, in one laboratory study.
compare: Platinum-tungsten is a heavy, high-melting wire metal with low electrical conductivity (2.58 to 2.77 % IACS in the Heraeus datasheet). The Heraeus datasheet gives its melting range as 1865 to 1885 °C. The rows below show the bulk alloy's density, melting range and modulus where a source gives them; no comparison with other materials was read in this run.
compare_rows:
- label: Density
benchmark: density
- label: Melting point
benchmark: melting_point
- label: Modulus of elasticity
benchmark: elastic_modulus
handling:
- Heraeus lists PtW8 as hardly formable, so plan forming steps with that in mind.
- Keep fine forms away from heat and ignition sources, since PubChem gives H228 for the platinum and tungsten element records.
- Use the temper and form with every strength value. The datasheet gives only ranges, with no temper stated.
good_for:
- Heat-resistant wire where density is acceptable. Heraeus lists PtW8 for resistance wire and spark plug electrodes.
- Sensor and probe wire. Goodfellow lists Pt92/W8 for sensor assemblies and microfabricated probe tips.
- Laboratory fuel-cell catalyst research on dealloyed PtCu/C, in acid electrolyte.
watch_out:
- Heavy for its size at 21.26 g/cm3.
- Low conductivity, 2.58 to 2.77 % IACS in the datasheet.
- The PtCu catalyst loses copper in acid during activation. The composition moves from PtCu1.3 to about PtCu0.25.
- No bulk Pt-Cu density, melting point or hardness was read in this run.
verdict: Platinum-tungsten is a dense, oxidation-resistant wire metal with datasheet values for density, melting range and mechanical strength. Platinum-copper is only covered here as a catalyst, and the bulk alloy needs a handbook source before it is used.
References
Every number above carries a reference number. Click one to see the source and where in it the value comes from.
| # | Source | Type | Year | Used for |
|---|---|---|---|---|
| Hera 158, PtW8, Heraeus Precious Metals datasheet (status 11/2021) | datasheet | 2021 | 11 values | |
| Goodfellow, Platinum/Tungsten Alloy Spooled Wire (Pt92/W8) product page | web | 2026 | 8 values | |
| PubChem compound record, Tungsten (CID 23964), GHS classification | database | 2026 | 1 value | |
| PubChem compound record, Platinum (CID 23939), GHS classification | database | 2026 | 1 value | |
| PubChem compound record, Copper (CID 23978), GHS classification | database | 2026 | 1 value | |
| Mineral Commodity Summaries 2026, Platinum-Group Metals chapter (U.S. Geological Survey, February 2026) | report | 2026 | 1 value | |
| Mineral Commodity Summaries 2026, Tungsten (U.S. Geological Survey, February 2026) | report | 2026 | 1 value | |
| Mineral Commodity Summaries 2026, Copper (U.S. Geological Survey, February 2026) | report | 2026 | 1 value | |
| Influence of Electrochemical Pretreatment Conditions of PtCu/C Alloy Electrocatalyst on Its Activity (Nanomaterials 11, 1499) | paper | 2021 | 9 values |