{ "spore": "profile", "id": "neodymium-iron-boron", "spore_version": "0.2", "family": "magnet-and-superconducting-alloys", "name": "Neodymium-iron-boron sintered magnet alloy", "abbreviation": "NdFeB", "role": "permanent magnet", "category": "metals", "type": "magnet-alloys", "summary": "Sintered NdFeB is the strongest commercial permanent magnet family. Its magnetic phase is Nd2Fe14B. Arnold's N42H datasheet gives a nominal remanence of 1300 mT and a maximum energy product of 330 kJ/m3, but a Curie temperature of only 310 degC, and Eclipse rates standard N42 for use up to 80 degC. It needs a coating against corrosion, is brittle, and loses magnetisation under neutron and charged-particle radiation.\n", "best_for": "Very high magnetic output per volume at moderate cost (N42H nominal remanence 1300 mT, maximum energy product 330 kJ/m3)", "weakest_at": "Heat (rated 80 degC for N42, 120 degC for N42H, Curie point 310 degC), corrosion without a coating, and demagnetisation by neutrons and charged particles", "identity": { "formula": "Nd2Fe14B", "designations": [], "source": "tomse-2024", "where": "Introduction (\"the Nd2Fe14B hard magnetic phase\"; Curie temperature 312 degC for the pure Nd-Fe-B ternary system); the CAS number was not found in a source we opened" }, "tags": { "environments": [], "stresses": [ "total-radiation-dose", "extreme-heat" ], "applications": [ "mechanisms", "electronics-and-chips" ] }, "properties": [ { "benchmark": "remanence_br", "label": "Remanence Br, grade N42H", "value": 1300, "bound": "exact", "unit": "mT", "scope": "material", "conditions": { "grade": "N42H", "temperature": "room temperature (not stated; datasheet typical values)", "value_type": "nominal (min 1280, max 1320)" }, "method": "Value listed in the manufacturer datasheet (13,000 Gauss nominal)", "status": "ground", "source": "arnold-n42h", "where": "Magnetic Properties table, row Br, Residual Induction, nominal column", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "remanence_br", "label": "Remanence Br, grade N42", "value": 1330, "bound": "exact", "unit": "mT", "scope": "material", "conditions": { "grade": "N42", "temperature": "20 degC", "value_type": "typical (minimum 1300)" }, "method": "Value listed in the manufacturer grade table", "status": "ground", "source": "eclipse-grades", "where": "Table \"Characteristic magnetic properties at room temperature (20 degC)\", row N42, column BR typ", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "coercivity_hcb", "label": "Normal coercivity HcB, grade N42H", "value": 979, "bound": "exact", "unit": "kA/m", "scope": "material", "conditions": { "grade": "N42H", "value_type": "nominal (min 955, max 1003)" }, "method": "Value listed in the manufacturer datasheet (12,300 Oersted)", "status": "ground", "source": "arnold-n42h", "where": "Magnetic Properties table, row HcB, Coercivity, nominal column", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "coercivity_hcj", "label": "Intrinsic coercivity HcJ, grade N42H", "value": 1353, "bound": "lower", "unit": "kA/m", "scope": "material", "conditions": { "grade": "N42H", "value_type": "minimum (17,000 Oersted)" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "source": "arnold-n42h", "where": "Magnetic Properties table, row HcJ, Intrinsic Coercivity", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "coercivity_hcj", "label": "Intrinsic coercivity HcJ, grade N42", "value": 955, "bound": "lower", "unit": "kA/m", "scope": "material", "conditions": { "grade": "N42", "temperature": "20 degC", "value_type": "minimum" }, "method": "Value listed in the manufacturer grade table", "status": "ground", "source": "eclipse-grades", "where": "Table \"Characteristic magnetic properties at room temperature (20 degC)\", row N42, column Hcj min", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "max_energy_product", "label": "Maximum energy product (BH)max, grade N42H", "value": 330, "bound": "exact", "unit": "kJ/m3", "scope": "material", "conditions": { "grade": "N42H", "value_type": "nominal (min 318, max 342; 42 MGOe)" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "source": "arnold-n42h", "where": "Magnetic Properties table, row BHmax, nominal column", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "max_energy_product", "label": "Maximum energy product (BH)max, grade N42", "value": 334, "bound": "exact", "unit": "kJ/m3", "scope": "material", "conditions": { "grade": "N42", "temperature": "20 degC", "value_type": "typical (minimum 318)" }, "method": "Value listed in the manufacturer grade table", "status": "ground", "source": "eclipse-grades", "where": "Table \"Characteristic magnetic properties at room temperature (20 degC)\", row N42, column BH(max) typ", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "curie_temperature", "label": "Curie temperature, grade N42H", "value": 310, "bound": "exact", "unit": "degC", "scope": "material", "conditions": { "grade": "N42H" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "source": "arnold-n42h", "where": "Thermal Properties table, row Curie Temperature, Tc", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "curie_temperature", "label": "Curie temperature, sintered NdFeB grades (supplier range)", "value": 310, "value_high": 340, "bound": "range", "unit": "degC", "scope": "material", "conditions": { "material": "sintered NdFeB, all grades in the table" }, "method": "Range listed in the manufacturer physical-properties table", "status": "ground", "source": "eclipse-grades", "where": "Physical properties at room temperature (20 degC), row Curie Temperature", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "curie_temperature", "label": "Curie temperature measured on a commercial Ni/Cu/Ni-coated magnet", "value": 310, "bound": "exact", "unit": "degC", "scope": "material", "conditions": { "method_detail": "DSC on about 100 mg sample, heated in air at 20 K/min to 1000 degC", "composition": "Nd 21.95, Pr 7.46, Dy 1.40 wt.%" }, "method": "Differential scanning calorimetry, endothermic peak", "status": "ground", "note": "The same paper reports 290 degC for a Ce-containing Zn-coated magnet and 340 degC for a Co- and Dy-rich epoxy-coated magnet, so Tc depends on composition.", "source": "tomse-2024", "where": "Results, discussion of Figure 1 (DSC curves); the paper gives 312 degC for the pure Nd2Fe14B phase", "source_detail": { "title": "Magnetic Performance and Anticorrosion Coating Stability of Thermally Demagnetized Nd-Fe-B Permanent Magnets for Reuse Applications", "id": "doi:10.3390/ma17235927", "url": "https://pmc.ncbi.nlm.nih.gov/articles/PMC11643009/", "year": 2024, "kind": "paper", "license": "open access (MDPI Materials)" } }, { "benchmark": "max_service_temp", "label": "Maximum operating temperature, grade N42", "value": 80, "bound": "exact", "unit": "degC", "scope": "material", "conditions": { "grade": "N42", "condition": "reference only; depends on the circuit", "permeance": "irreversible losses avoided at L/D = 0.7" }, "method": "Value listed in the manufacturer grade table", "status": "ground", "source": "eclipse-grades", "where": "Table \"Characteristic magnetic properties\", row N42, column Max. operating temp.; Remarks on facing table, notes 1 and 3", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "max_service_temp", "label": "Maximum operating temperature, grade N42H", "value": 120, "bound": "exact", "unit": "degC", "scope": "material", "conditions": { "grade": "N42H", "condition": "reference only; depends on the circuit" }, "method": "Value listed in the manufacturer grade table", "status": "ground", "source": "eclipse-grades", "where": "Table \"Characteristic magnetic properties\", row N42H, column Max. operating temp.; Remarks on facing table, note 1", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "max_service_temp", "label": "Working temperature, grade N42", "value": 80, "bound": "exact", "unit": "degC", "scope": "material", "conditions": { "grade": "N42", "note": "datasheet label is Working Temperature (Tw)" }, "method": "Value listed in the supplier's online specification page", "status": "ground", "source": "indigo-n42", "where": "Specifications table, row Working Temperature (Tw)", "source_detail": { "title": "Specifications for Fully Sintered/Pressed Neodymium Magnets, N42 Grade", "url": "https://www.indigoinstruments.com/N42-Magnet-Specs.php", "kind": "web", "license": "supplier web page" } }, { "benchmark": "temp_coeff_br", "label": "Reversible temperature coefficient of remanence, alpha(Br), grade N42H", "value": -0.12, "bound": "exact", "unit": "%/degC", "scope": "material", "conditions": { "grade": "N42H", "range": "measured between 20 and 120 degC" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "source": "arnold-n42h", "where": "Thermal Properties table, row of Induction alpha(Br) and note (1)", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "temp_coeff_br", "label": "Temperature coefficient of Br, sintered NdFeB", "value": -0.11, "bound": "exact", "unit": "%/degC", "scope": "material", "conditions": { "material": "sintered NdFeB, all grades in the table", "temperature": "room temperature" }, "method": "Value listed in the manufacturer physical-properties table", "status": "ground", "source": "eclipse-grades", "where": "Physical properties at room temperature (20 degC), row Temp. Coeff. Of Br", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "temp_coeff_hcj", "label": "Reversible temperature coefficient of coercivity, alpha(Hcj), grade N42H", "value": -0.57, "bound": "exact", "unit": "%/degC", "scope": "material", "conditions": { "grade": "N42H", "range": "measured between 20 and 120 degC" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "source": "arnold-n42h", "where": "Thermal Properties table, row of Coercivity alpha(Hcj) and note (1)", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "temp_coeff_hcj", "label": "Temperature coefficient of iHc, sintered NdFeB", "value": -0.6, "bound": "exact", "unit": "%/degC", "scope": "material", "conditions": { "material": "sintered NdFeB, all grades in the table", "temperature": "room temperature" }, "method": "Value listed in the manufacturer physical-properties table", "status": "ground", "source": "eclipse-grades", "where": "Physical properties at room temperature (20 degC), row Temp. Coeff of iHc", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "cte", "label": "Thermal expansion, parallel to magnetisation (C //), grade N42H", "value": 7, "bound": "exact", "unit": "1e-6 per degC (dL/L)", "scope": "material", "conditions": { "grade": "N42H", "range": "20 to 200 degC", "direction": "parallel to the magnetisation direction" }, "method": "Typical value listed in the manufacturer datasheet", "status": "ground", "note": "The same row gives -1 perpendicular to the magnetisation direction, so the expansion is strongly anisotropic.", "source": "arnold-n42h", "where": "Thermal Properties table, row Coefficient of Thermal Expansion, note (2)", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "cte", "label": "Coefficient of thermal expansion, sintered NdFeB", "value": 4, "bound": "exact", "unit": "1e-6 per degC", "scope": "material", "conditions": { "material": "sintered NdFeB, all grades in the table", "temperature": "room temperature" }, "method": "Value listed in the manufacturer physical-properties table", "status": "ground", "source": "eclipse-grades", "where": "Physical properties at room temperature (20 degC), row Coeff. Of Thermal Expansion", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "thermal_conductivity", "label": "Thermal conductivity, grade N42H (parallel)", "value": 5.3, "bound": "exact", "unit": "kcal/(m h degC)", "scope": "material", "conditions": { "grade": "N42H", "direction": "parallel to the magnetisation direction" }, "method": "Typical value listed in the manufacturer datasheet", "status": "ground", "note": "Unit as printed in the source. The perpendicular value in the same row is 5.8.", "source": "arnold-n42h", "where": "Thermal Properties table, row Thermal Conductivity", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "density", "label": "Density, grade N42H", "value": 7.6, "bound": "exact", "unit": "g/cm3", "scope": "material", "conditions": { "grade": "N42H" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "source": "arnold-n42h", "where": "Other Properties table, row Density", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "density", "label": "Density, sintered NdFeB", "value": 7.5, "bound": "exact", "unit": "g/cm3", "scope": "material", "conditions": { "material": "sintered NdFeB, all grades in the table", "temperature": "20 degC" }, "method": "Value listed in the manufacturer physical-properties table", "status": "ground", "note": "The source prints \"7.5/cm3\"; g is assumed from context.", "source": "eclipse-grades", "where": "Physical properties at room temperature (20 degC), row Density", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "vickers_hardness", "label": "Vickers hardness, grade N42H", "value": 620, "bound": "exact", "unit": "Hv", "scope": "material", "conditions": { "grade": "N42H", "load": "not stated" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "source": "arnold-n42h", "where": "Other Properties table, row Hardness, Vickers", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "flexural_strength", "label": "Flexural strength, grade N42H", "value": 285, "bound": "exact", "unit": "MPa", "scope": "material", "conditions": { "grade": "N42H", "test": "not stated" }, "method": "Value listed in the manufacturer datasheet (41,300 psi)", "status": "ground", "source": "arnold-n42h", "where": "Other Properties table, row Flexural Strength", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "tensile_strength", "label": "Tensile strength, sintered NdFeB", "value": 8, "bound": "exact", "unit": "kg/mm2", "scope": "material", "conditions": { "material": "sintered NdFeB, all grades in the table", "temperature": "20 degC" }, "method": "Value listed in the manufacturer physical-properties table", "status": "ground", "note": "Unit as printed in the source (kilogram-force per square millimetre).", "source": "eclipse-grades", "where": "Physical properties at room temperature (20 degC), row Tensile Strength", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "youngs_modulus", "label": "Young's modulus, sintered NdFeB", "value": 160000000000, "bound": "exact", "unit": "N/m2", "scope": "material", "conditions": { "material": "sintered NdFeB, all grades in the table", "temperature": "20 degC" }, "method": "Value listed in the manufacturer physical-properties table", "status": "ground", "source": "eclipse-grades", "where": "Physical properties at room temperature (20 degC), row Young's Modulus", "source_detail": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "electrical_resistivity", "label": "Electrical resistivity, grade N42H (parallel)", "value": 150, "bound": "exact", "unit": "uohm cm", "scope": "material", "conditions": { "grade": "N42H", "direction": "parallel to the magnetisation direction" }, "method": "Value listed in the manufacturer datasheet", "status": "ground", "note": "The perpendicular value in the same row is 130.", "source": "arnold-n42h", "where": "Other Properties table, row Electrical Resistivity", "source_detail": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" } }, { "benchmark": "nd_content_hdd_magnets", "label": "Neodymium content of hard-drive magnets", "value": 22.9, "bound": "exact", "unit": "wt.%", "scope": "material", "conditions": { "sample": "magnets from desktop and notebook PC hard disk drives", "variation": "standard deviation +/- 2.8" }, "method": "Chemical analysis of dismantled hard-drive magnets (the item page reports the mean and deviation)", "status": "ground", "source": "ueberschaar-2015", "where": "Repository item page, Nd/Pr/Dy concentrations in the magnets", "source_detail": { "title": "Enabling the recycling of rare earth elements through product design and trend analyses of hard disk drives", "id": "doi:10.14279/depositonce-6368", "url": "https://depositonce.tu-berlin.de/items/99e52b20-ebd0-479d-b0ac-341c8996112c", "year": 2015, "kind": "paper", "license": "In Copyright (item page)" } }, { "benchmark": "pr_content_hdd_magnets", "label": "Praseodymium content of hard-drive magnets", "value": 2.7, "bound": "exact", "unit": "wt.%", "scope": "material", "conditions": { "sample": "magnets from desktop and notebook PC hard disk drives", "variation": "standard deviation +/- 2.2" }, "method": "Chemical analysis of dismantled hard-drive magnets", "status": "ground", "source": "ueberschaar-2015", "where": "Repository item page, Nd/Pr/Dy concentrations in the magnets", "source_detail": { "title": "Enabling the recycling of rare earth elements through product design and trend analyses of hard disk drives", "id": "doi:10.14279/depositonce-6368", "url": "https://depositonce.tu-berlin.de/items/99e52b20-ebd0-479d-b0ac-341c8996112c", "year": 2015, "kind": "paper", "license": "In Copyright (item page)" } }, { "benchmark": "dy_content_hdd_magnets", "label": "Dysprosium content of hard-drive magnets", "value": 1.4, "bound": "exact", "unit": "wt.%", "scope": "material", "conditions": { "sample": "magnets from desktop and notebook PC hard disk drives", "variation": "standard deviation +/- 1.5" }, "method": "Chemical analysis of dismantled hard-drive magnets", "status": "ground", "source": "ueberschaar-2015", "where": "Repository item page, Nd/Pr/Dy concentrations in the magnets", "source_detail": { "title": "Enabling the recycling of rare earth elements through product design and trend analyses of hard disk drives", "id": "doi:10.14279/depositonce-6368", "url": "https://depositonce.tu-berlin.de/items/99e52b20-ebd0-479d-b0ac-341c8996112c", "year": 2015, "kind": "paper", "license": "In Copyright (item page)" } }, { "benchmark": "tid", "label": "Gamma dose with no demagnetisation seen (1.17 MeV gammas)", "value": 280, "bound": "lower", "unit": "Mrad", "scope": "material", "conditions": { "radiation": "1.17 MeV gamma rays", "result": "no demagnetisation observed" }, "method": "Reported in the paper's introduction from earlier experiments (not new measurements)", "status": "ground", "source": "simos-2008", "where": "Introduction, sentence on electron and gamma irradiation", "source_detail": { "title": "An Experimental Study of Radiation-Induced Demagnetization of Insertion Device Permanent Magnets", "id": "EPAC08 WEPC053", "url": "https://proceedings.jacow.org/e08/papers/WEPC053.pdf", "year": 2008, "kind": "paper", "license": "JACoW proceedings" } }, { "benchmark": "flux_loss_17mev_electrons", "label": "Flux loss after 17 MeV electron irradiation", "value": 9, "bound": "exact", "unit": "%", "scope": "material", "conditions": { "radiation": "17 MeV electrons", "dose": "260 Mrad" }, "method": "Reported in the paper's introduction from earlier experiments (not new measurements)", "status": "ground", "source": "simos-2008", "where": "Introduction, sentence on electron and gamma irradiation", "source_detail": { "title": "An Experimental Study of Radiation-Induced Demagnetization of Insertion Device Permanent Magnets", "id": "EPAC08 WEPC053", "url": "https://proceedings.jacow.org/e08/papers/WEPC053.pdf", "year": 2008, "kind": "paper", "license": "JACoW proceedings" } }, { "benchmark": "field_loss_esrf_undulators", "label": "Field loss in operating insertion devices (ESRF)", "value": 8, "bound": "upper", "unit": "%", "scope": "material", "conditions": { "setting": "insertion-device magnets in a synchrotron light source", "dose": "several Mrad" }, "method": "Operating experience quoted in the paper's introduction (\"as much as 8%\")", "status": "ground", "source": "simos-2008", "where": "Introduction, paragraph on serious demagnetisation observed in operating light sources", "source_detail": { "title": "An Experimental Study of Radiation-Induced Demagnetization of Insertion Device Permanent Magnets", "id": "EPAC08 WEPC053", "url": "https://proceedings.jacow.org/e08/papers/WEPC053.pdf", "year": 2008, "kind": "paper", "license": "JACoW proceedings" } }, { "benchmark": "flux_loss_14mev_neutrons", "label": "Flux loss of grade N44H after 14 MeV neutrons", "value": 6.4, "bound": "exact", "unit": "%", "scope": "material", "conditions": { "radiation": "monoenergetic 14 MeV neutrons", "fluence": "3.64e13 n/cm2", "grade": "N44H", "permeance": "Pc = 1.2" }, "method": "Earlier experiment (Kawakubo et al.) as reported in the 65 MeV paper's discussion", "status": "ground", "note": "Same experiment reported losses from 37% to 1% across grades with coercivity from 880 to 2400 kA/m, so higher coercivity resisted neutrons much better.", "source": "marechal-2006", "where": "Discussion, paragraph on the 14 MeV experiment", "source_detail": { "title": "65 MeV Neutron Irradiation of Nd-Fe-B Permanent Magnets", "id": "EPAC06 THPCH135", "url": "https://accelconf.web.cern.ch/e06/PAPERS/THPCH135.PDF", "year": 2006, "kind": "paper", "license": "JACoW proceedings" } }, { "benchmark": "neutron_fluence_no_loss_65mev", "label": "Fluence of 65 MeV neutrons with no demagnetisation observed", "value": 2400000000, "bound": "lower", "unit": "n/cm2", "scope": "material", "conditions": { "radiation": "65 MeV neutrons, fluence 2.4e9 n/cm2, magnet at 25 degC", "grades": "four Neomax grades, TiN coated, 8 x 8 x 8 mm", "magnetisation": "parallel to the beam" }, "method": "Neutron irradiation at the TIARA cyclotron, change in field measured with a Hall probe", "status": "ground", "source": "marechal-2006", "where": "Results, text and Figure 3", "source_detail": { "title": "65 MeV Neutron Irradiation of Nd-Fe-B Permanent Magnets", "id": "EPAC06 THPCH135", "url": "https://accelconf.web.cern.ch/e06/PAPERS/THPCH135.PDF", "year": 2006, "kind": "paper", "license": "JACoW proceedings" } } ], "corrosion": [ { "environment": "Humid or wet conditions, uncoated magnet", "headline": "The Nd-rich grain-boundary phases corrode", "effect": "The Nd-rich secondary phases are prone to corrosion because neodymium has a very negative reduction potential, and this degrades magnetic performance. Coatings are the usual remedy.", "rating": "unknown", "conditions": { "reduction_potential_of_Nd": "-2.32 V", "note": "no corrosion rate in a source we opened" }, "source": "tomse-2024", "where": "Introduction, paragraph on multiphase structure" }, { "environment": "Ni/Cu/Ni plated magnet heated to 380 degC (thermal demagnetisation)", "headline": "Nickel-copper-nickel coating survived heating", "effect": "The Ni/Cu/Ni coating stayed stable after 30 min at 380 degC in air and in vacuum, and the magnetic performance was completely recovered on remagnetisation. A Zn coating was not compatible, and epoxy decomposed in air.", "rating": "low", "conditions": { "heating": "380 degC for 30 min", "atmosphere": "air or vacuum" }, "source": "tomse-2024", "where": "Abstract, Results (coating stability and Figure 2)" } ], "risks": { "hazards": [ { "text": "Neodymium metal (PubChem CID 23934): signal word Danger. Notified hazards are H228 flammable solid (34.3%), H251 self-heating, may catch fire (33.3%), H315 causes skin irritation (41.9%), H319 causes serious eye irritation (41.9%) and H413 may cause long lasting harmful effects to aquatic life (10.6%). PubChem says 56.4% of 463 reports do not meet GHS criteria. This describes the pure metal, not the solid magnet.", "ghs": [ "H228", "H251", "H315", "H319", "H413" ], "source": "pubchem-neodymium", "where": "GHS Classification section" }, { "text": "Boron (PubChem CID 5462311): signal word Warning. Notified hazard H302 harmful if swallowed (46.4%). PubChem says 52.2% of 485 reports do not meet GHS criteria.", "ghs": [ "H302" ], "source": "pubchem-boron", "where": "GHS Classification section" }, { "text": "Iron (PubChem CID 23925): 74.1% of 6013 reports do not meet GHS criteria. The notified hazards are H228 flammable solid (15.5%) and H251 self-heating, may catch fire (21.2%), signal word Danger.", "ghs": [ "H228", "H251" ], "source": "pubchem-iron", "where": "GHS Classification section" }, { "text": "Solid NdFeB magnet (Digikey supplier SDS): signal word Danger. Hazard codes H260 and H261 are listed for chemical hazards, and prolonged immersion in water or acid can form hydrogen, which could ignite spontaneously in some environments. Health codes H317, H332 and H302 are listed. Broken magnets can have sharp chips and shards.", "ghs": [ "H260", "H261", "H317", "H332", "H302" ], "source": "digikey-ndfeb-sds", "where": "Section 2 Hazards Identification" }, { "text": "Solid NdFeB magnet (Allstar supplier SDS, Rev 1.0): not classified under GHS-US for the solid, and no label elements apply. The SDS says the hazards arise when the metal is processed, for example as powder or in welding.", "ghs": [], "source": "allstar-ndfeb-sds", "where": "Sections 2.1, 2.2 and 2.3" }, { "text": "Fire risk of NdFeB dust and powder: fine powders oxidise, smoulder and burn rapidly in air or oxygen. Very fine powder (200 mesh) is rated a weak explosive hazard when suspended in air. Cutting, grinding or smashing a magnet can spark and start a fire in a flammable atmosphere. The SDS says the solid is incombustible but can burn as powder or dust.", "ghs": [], "source": "digikey-ndfeb-sds", "where": "Section 2 (unusual fire and explosion hazards) and Section 5" }, { "text": "Fire risk of NdFeB powder (Allstar SDS): dry powders or magnets oxidise, smolder and burn rapidly in air. Dust clouds suspended in air can be explosive, and dust deposits can form an explosive mixture. Powders should be kept in water slurry or under nitrogen or argon. Use earth, sand or Class D dry powder; do not use water or halon agents.", "ghs": [], "source": "allstar-ndfeb-sds", "where": "Section 5 Fire-Fighting Measures and Section 7" } ], "failure_risks": [ { "mode": "Demagnetisation by heat", "trigger": "Operating above the grade's maximum temperature or heating above the Curie point", "consequence": "Loss of magnetisation. Heating above Tc is used on purpose to demagnetise magnets for recycling; the Ni/Cu/Ni magnet regained full performance on remagnetisation after 30 min at 380 degC.", "severity": "high", "source": "tomse-2024", "where": "Introduction and Results" }, { "mode": "Demagnetisation by neutrons and charged particles", "trigger": "High-energy neutrons, protons, or electrons in accelerators", "consequence": "Flux loss of up to 9% at 260 Mrad of 17 MeV electrons, while gammas alone caused none at 280 Mrad. The same paper says charged particles and high-energy neutrons are very effective at demagnetising magnets.", "severity": "high", "source": "simos-2008", "where": "Introduction" }, { "mode": "Demagnetisation by thermal-neutron capture on boron", "trigger": "Thermal neutron irradiation", "consequence": "Remanent magnetisation changes substantially because of the 10B(n,alpha)7Li reaction; the paper reports no change in coercivity.", "severity": "moderate", "source": "klaffky-2006", "where": "Abstract and Magnetic Measurements" }, { "mode": "Chipping and brittleness", "trigger": "Mechanical handling and impact", "consequence": "The BNL magnets were plated with a thin nickel coating to eliminate chipping. Hydrogen processing embrittles and pulverises end-of-life magnets, which is used for recycling.", "severity": "moderate", "source": "simos-2008", "where": "Experimental Effort paragraph" } ], "side_effects": [ { "text": "Irradiated magnets become radioactive: after about 12 months of cool-down they were measured remotely in a hot cell, and the isotopes formed were computed with the ORIGEN code.", "affects": "Handling and replacement of magnets in radiation areas", "source": "simos-2008", "where": "Post-irradiation results" } ], "handling": [ { "text": "The manufacturer says the maximum working temperature is for reference only and depends on the circuit the magnet operates in.", "source": "eclipse-grades", "where": "Remarks on facing table" }, { "text": "Customers are advised to consult the supplier for applications near 150 degC.", "source": "eclipse-grades", "where": "Remarks on facing table" }, { "text": "Broken magnets have sharp chips and shards that can cut skin. Impacts can throw chips or bits of magnet material at speed, so wear eye protection, and wear gloves for long handling.", "source": "digikey-ndfeb-sds", "where": "Section 2 and handling section" }, { "text": "Strong attraction can clamp fingers or skin between magnets or onto ferrous parts. Strong magnetic fields may affect pacemakers and other implanted medical devices.", "source": "allstar-ndfeb-sds", "where": "Sections 2.3 and 7.1" }, { "text": "Do not breathe dust or powder, and avoid creating or spreading it. Clean up released powder by sweeping or shovelling into sealed containers, not with a vacuum cleaner, because deposits can form an explosive mixture.", "source": "digikey-ndfeb-sds", "where": "Cleanup of released powders (accidental release section)" }, { "text": "Dust should not accumulate on surfaces. Eliminate ignition sources where dust forms, and take up spills mechanically (sweeping, shovelling) to avoid generating dust.", "source": "allstar-ndfeb-sds", "where": "Sections 6 and 7" } ], "mitigations": [ { "text": "Higher-coercivity grades resist neutrons far better: in the 14 MeV test the loss ranged from 37% to 1% as coercivity rose from 880 to 2400 kA/m.", "source": "marechal-2006", "where": "Discussion" }, { "text": "Ni/Cu/Ni plating is the coating that stayed stable through heating; 5 micrometre TiN was used on the 65 MeV test magnets.", "source": "tomse-2024", "where": "Abstract and Results" } ] }, "uses": [ { "application": "electronics-and-chips", "device": "Earbud headphones", "example": "Apple's launch press release for the first iPod (2001) says its earbud-style headphones use neodymium magnets, for frequency response and sound quality.", "source": "apple-ipod-press-release", "where": "Paragraph on the earbud headphones" }, { "application": "electronics-and-chips", "device": "Hard disk drive magnets", "example": "German PC hard-drive magnets analysed at TU Berlin for rare earth recycling.", "source": "ueberschaar-2015", "where": "Abstract" }, { "application": "mechanisms", "device": "Electric motors, wind turbines, consumer electronics and home appliances", "example": "Listed by the 2024 coating study as the main uses of Nd-Fe-B magnets.", "source": "tomse-2024", "where": "Introduction, first sentence" }, { "application": "mechanisms", "device": "Undulator and insertion-device magnet arrays in synchrotron light sources", "example": "SPring-8 uses in-vacuum undulators whose magnets sit a few millimetres from the electron beam.", "source": "marechal-2006", "where": "Introduction" } ], "supply": [ { "subject": "Rare earths (Nd, Pr, Dy)", "abundance": "World mine production was 390,000 tons of rare-earth oxide equivalent in 2024, of which China mined 270,000 tons (about 69%, computed from the table). Reserves: China 44,000,000 tons, world more than 90,000,000 tons.", "producers": [ { "country": "China", "share_percent": 69.2, "year": 2024 }, { "country": "United States", "share_percent": 11.5, "year": 2024 }, { "country": "Burma", "share_percent": 7.9, "year": 2024 } ], "critical_lists": [ { "list": "EU critical raw materials 2023 (heavy and light rare earth elements)", "listed": true } ], "recycling": "USGS reports that limited quantities of rare earths were recovered from batteries, permanent magnets and fluorescent lamps. The EU Critical Raw Materials Act sets a goal of recycling 25% of magnets by 2030 (as cited by the 2024 coating study).", "substitutes": [ "Substitutes are available for many applications but generally are less effective (USGS)." ], "source": "usgs-mcs-2025-re", "where": "Salient statistics, World Mine Production and Reserves table, Recycling, Substitutes" }, { "subject": "Heavy rare earths and boron (EU supply)", "abundance": "The EU page states China provides 100% of EU supply of heavy rare earth elements and Turkey provides 99% of EU boron supply.", "producers": [], "critical_lists": [ { "list": "EU critical raw materials 2023: heavy rare earth elements", "listed": true }, { "list": "EU critical raw materials 2023: light rare earth elements", "listed": true }, { "list": "EU critical raw materials 2023: boron/borate", "listed": true } ], "substitutes": [], "source": "eu-crm-page", "where": "Fifth list of critical raw materials (2023) and supply concentration figures" } ], "media": [], "documents": [ { "title": "Arnold Magnetic Technologies N42H sintered NdFeB datasheet", "type": "datasheet", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021 }, { "title": "Eclipse Magnetics sintered NdFeB grades data", "type": "datasheet", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011 }, { "title": "USGS Mineral Commodity Summaries 2025: Rare earths", "type": "report", "url": "https://pubs.usgs.gov/periodicals/mcs2025/mcs2025-rare-earths.pdf", "year": 2025 }, { "title": "NETL Life Cycle Inventory: NdFeB Permanent Magnet Manufacturing (DF_Stage1_O)", "type": "report", "url": "https://netl.doe.gov/projects/files/DF_Stage1_O_NdFeB_Magnet_Manufacturing-2014-01.pdf", "year": 2014 }, { "title": "Allstar Magnetics SDS, Neodymium Iron Boron (NdFeB) Magnet, Rev 1.0", "type": "sds", "url": "https://allstarmagnetics.com/wp-content/uploads/2024/10/Neodymium-SDS.pdf", "year": 2024 }, { "title": "SDS/MSDS, NdFeB Magnets (Digikey supplier data sheet)", "type": "sds", "url": "https://mm.digikey.com/Volume0/opasdata/d220001/medias/docus/5849/SDS_MSDS%20-%20NdFeB%20Magnets.pdf" }, { "title": "PubChem compound records: neodymium (CID 23934), boron (CID 5462311), iron (CID 23925)", "type": "database", "url": "https://pubchem.ncbi.nlm.nih.gov/compound/23934" } ], "gaps": [ "Use in spacecraft or in orbit: no flight or space-qualification source was found for sintered NdFeB (no NASA/ESA report, vacuum outgassing value, or thermal-cycling result).", "Melt-spinning route: only a Wikipedia page was read for the process (secondary). No primary melt-spinning paper or datasheet was opened.", "Atomic weights are PubChem values printed to two decimals (Nd 144.24, Fe 55.84, B 10.81). No IUPAC table value was read.", "PubChem GHS data are aggregated company notifications to the ECHA inventory, not one SDS for the magnet. The magnet hazards rest on two supplier SDSs (Digikey and Allstar).", "CAS number and crystal structure of Nd2Fe14B: not taken from a source we opened.", "Quantified corrosion rate or salt-spray hours for coated or uncoated magnets: not found in an opened source.", "Nickel coating thickness and coating-specific performance (the datasheets say to contact the supplier for coating recommendations).", "Grade-by-grade coefficients and curves for temperatures above 120 degC (the Arnold coefficients are valid only between 20 and 120 degC).", "Quantified irreversible flux loss versus temperature (the sources give only maximum working temperatures).", "Recycling rate for NdFeB magnets: no quantified rate from a primary source (only the 25% 2030 goal quoted in a paper and the USGS wording 'limited quantities').", "Radiation tolerance in orbit (protons, electrons, galactic cosmic rays at spacecraft magnet locations): only accelerator experiments were found.", "Brittleness measured as fracture toughness: only flexural strength (285 MPa) and tensile strength (8.0 kg/mm2) were found." ], "story": { "why": "Neodymium-iron-boron (NdFeB) is a sintered alloy whose magnetic phase is Nd2Fe14B. Sintered means the powder is pressed and fused by heat. It is the strongest family of commercial permanent magnets, meaning magnets that keep their magnetisation without power. Arnold's N42H datasheet gives a nominal remanence of 1300 mT, the field the magnet keeps after magnetising, and a maximum energy product of 330 kJ/m3, a measure of how much magnetic work it can do per volume. The price of that strength is sensitivity. The Curie temperature, above which a magnet loses its magnetism, is only 310 degC, and Eclipse rates standard N42 for use up to 80 degC and N42H up to 120 degC. It also needs a coating against corrosion and is brittle.", "uses": [ { "where": "Hard disk drives", "line": "A TU Berlin study of PC hard drives measured 22.9% neodymium, 2.7% praseodymium and 1.4% dysprosium in the magnets, which shows how much rare earth sits in everyday electronics." }, { "where": "Motors, wind turbines and appliances", "line": "A 2024 coating study lists electric motors, wind turbines, consumer electronics and home appliances as the main uses of Nd-Fe-B magnets." }, { "where": "Synchrotron light sources", "line": "SPring-8 uses in-vacuum undulators with the magnets a few millimetres from the electron beam, where radiation demagnetisation becomes a design issue." } ], "can_do": [ { "label": "Magnetic strength", "line": "Grade N42H has a nominal remanence of 1300 mT and a maximum energy product of 330 kJ/m3 (Arnold datasheet). The Eclipse table gives 1330 mT and 334 kJ/m3 typical for grade N42.", "scope": "material", "value": "1300 mT" }, { "label": "Resisting demagnetising fields", "line": "Grade N42H has a minimum intrinsic coercivity of 1353 kA/m, against a minimum of 955 kA/m for plain N42. Coercivity is the opposing field the magnet can take before it loses magnetisation.", "scope": "material", "value": "1353 kA/m" }, { "label": "Heat", "line": "Eclipse lists a maximum operating temperature of 80 degC for N42 and 120 degC for N42H. It calls this a reference only and says it depends on the circuit. The remanence also falls as it warms, by 0.12% per degC (Arnold, 20 to 120 degC), and coercivity by 0.57% per degC.", "scope": "material", "value": "Rated 80 degC (N42)" }, { "label": "Radiation", "line": "An accelerator paper reports no demagnetisation after 280 Mrad of 1.17 MeV gamma rays but a 9% flux loss after 260 Mrad of 17 MeV electrons. These values come from earlier experiments quoted in the paper.", "scope": "material", "value": "No loss at 280 Mrad of gamma" }, { "label": "Stiffness and hardness", "line": "Arnold gives a Vickers hardness of 620 Hv and a flexural strength of 285 MPa for N42H, with a density of 7.6 g/cm3.", "scope": "material", "value": "620 Hv" } ], "compare": "Within sintered NdFeB, the grade suffix trades strength for heat tolerance. Plain N42 has an intrinsic coercivity of at least 955 kA/m and is rated to 80 degC. N42H keeps the same nominal remanence class but raises the coercivity to at least 1353 kA/m and the rating to 120 degC. Coercivity also decides radiation tolerance: in a 14 MeV neutron test the loss ranged from 37% to 1% as coercivity rose from 880 to 2400 kA/m.", "compare_rows": [ { "label": "Remanence (N42H)", "benchmark": "remanence_br", "scope": "material" }, { "label": "Maximum energy product", "benchmark": "max_energy_product", "scope": "material" }, { "label": "Curie temperature", "benchmark": "curie_temperature", "scope": "material" }, { "label": "Maximum working temperature", "benchmark": "max_service_temp", "scope": "material" }, { "label": "Density", "benchmark": "density", "scope": "material" } ], "handling": [ "Check the grade's maximum temperature and the magnet's shape before use: the supplier says the rating depends on the circuit.", "Keep it coated. Nd-rich phases corrode, and Ni/Cu/Ni plating is the coating that survived heating in the 2024 study.", "Treat irradiated magnets as radioactive; the BNL magnets were left for about 12 months and measured in a hot cell." ], "good_for": [ "Strong fields from small volumes where temperatures stay below the grade's rating.", "Applications where cost matters more than the heat tolerance of samarium-cobalt (not compared with a source here)." ], "watch_out": [ "Low Curie point (310 degC) and a working limit of only 80 to 120 degC for these grades.", "Loss of magnetisation in neutron and charged-particle fields, and secondary radioactivity afterwards.", "Corrosion of the Nd-rich phases without coating, and brittle chipping.", "Supply: China mined 270,000 of 390,000 tons of rare-earth oxide in 2024, and the EU states China supplies 100% of its heavy rare earths." ], "verdict": "A very strong magnet material for ordinary temperatures, backed by good sourced datasheet numbers, but its heat limit, corrosion sensitivity, brittleness and radiation sensitivity mean it must be chosen by grade and protected. No space-flight data were found, so its fitness for spacecraft is unproven here.", "recipe": { "line": "Nd2Fe14B is the hard magnetic phase: two neodymium atoms, fourteen iron atoms and one boron atom per formula unit. Commercial magnets are not pure Nd2Fe14B. They carry praseodymium, dysprosium and cobalt, and a typical alloy is about 72% iron, 27% neodymium and 1% boron by weight. Sintered magnets are made by strip casting the melt, hydrogen decrepitation, jet milling, aligning and pressing the powder, and vacuum sintering at 1000 degC. Dysprosium and cobalt raise the Curie temperature: the epoxy-coated grade with 11.39 wt.% Dy and 2.23 wt.% Co reached 340 degC, against 310 degC for the Ni/Cu/Ni grade with 1.40 wt.% Dy. Melt spinning is the other route: the melt is quenched on a drum into ribbon, milled to powder and bonded into polymer for moulded magnets.", "parts": [ { "name": "Neodymium", "symbol": "Nd", "role": "The rare-earth atoms of the hard phase. The alloy also carries praseodymium and dysprosium in varying amounts.", "atoms": 2, "atomic_weight": 144.24, "source": "pubchem-neodymium" }, { "name": "Iron", "symbol": "Fe", "role": "Most of the alloy by weight, about 72% in a typical alloy.", "atoms": 14, "atomic_weight": 55.84, "source": "pubchem-iron" }, { "name": "Boron", "symbol": "B", "role": "The single boron atom per formula unit. Its 10B isotope captures thermal neutrons, which changes remanence in irradiated magnets.", "atoms": 1, "atomic_weight": 10.81, "source": "pubchem-boron" } ] }, "risk_groups": [ { "title": "For people", "lead": "No safety data sheet was opened, so no classification is stated.", "points": [ { "label": "Irradiated magnets", "line": "Magnets irradiated at BNL were left to cool down for about 12 months and then measured remotely in a hot cell, because the exposure creates radioactive isotopes." } ], "gap": "Safety data sheet hazards were not found in an opened source.", "level": 1, "verdict": "No hazard data found" }, { "title": "If it fails", "lead": "The loss of magnetisation depends on grade, shape and the radiation type.", "points": [ { "label": "Heat", "line": "Heating above the Curie temperature (310 degC for the measured magnet) demagnetises it. A Ni/Cu/Ni magnet heated 30 min at 380 degC regained full performance when remagnetised." }, { "label": "Charged particles", "line": "260 Mrad of 17 MeV electrons caused 9% flux loss, while 280 Mrad of gamma caused none." }, { "label": "Neutrons", "line": "In a 14 MeV test grade N44H lost 6.4% at 3.64e13 n/cm2, and in a 65 MeV test no change was seen up to 2.4e9 n/cm2." } ], "level": 3, "verdict": "Heat and radiation demagnetise it" }, { "title": "Handling and storage", "points": [ { "label": "Temperature", "line": "Stay within the rated working temperature and ask the supplier for applications near 150 degC." }, { "label": "Coating", "line": "Protect the surface: the BNL magnets were nickel plated, partly to eliminate chipping." } ] } ] }, "updated": "2026-10-16", "review": { "status": "draft", "method": "assistant", "checked_values": 35, "unreachable": 0, "caveats": 4, "note": "Written by an AI assistant on 2026-10-17. The Arnold N42H and Eclipse grade values, the USGS table, the Simos and Marechal and Klaffky paper statements, and the Tomse 2024 paper values were read in text extracted from the source PDFs or page. The Indigo page and the TU Berlin item page and the EU page were read once through a web-page summary and not independently re-read. Radiation values from Simos 2008 and the 14 MeV neutron value from Marechal 2006 are secondary: the papers quote earlier experiments. The Eclipse sheet is a 2011 PDF. No values were taken from memory. Producer shares (11.5% US, 7.9% Burma) are computed from USGS table rows by this assistant." }, "sources": { "apple-ipod-press-release": { "title": "Apple Presents iPod (press release)", "id": "Apple Inc., 23 October 2001", "url": "https://www.apple.com/newsroom/2001/10/23Apple-Presents-iPod/", "year": 2001, "kind": "web" }, "arnold-n42h": { "title": "N42H Sintered Neodymium-Iron-Boron Magnets (datasheet, Rev. 210607)", "id": "N42H-151021", "url": "https://www.arnoldmagnetics.com/wp-content/uploads/2017/11/N42H-151021.pdf", "year": 2021, "kind": "datasheet", "license": "manufacturer datasheet" }, "eclipse-grades": { "title": "Sintered Neodymium Iron Boron (NdFeB) Magnets, grades data", "id": "neodymium_grades_data.pdf", "url": "https://www.eclipsemagnetics.com/site/assets/files/2399/neodymium_grades_data.pdf", "year": 2011, "kind": "datasheet", "license": "manufacturer datasheet" }, "indigo-n42": { "title": "Specifications for Fully Sintered/Pressed Neodymium Magnets, N42 Grade", "url": "https://www.indigoinstruments.com/N42-Magnet-Specs.php", "kind": "web", "license": "supplier web page" }, "tomse-2024": { "title": "Magnetic Performance and Anticorrosion Coating Stability of Thermally Demagnetized Nd-Fe-B Permanent Magnets for Reuse Applications", "id": "doi:10.3390/ma17235927", "url": "https://pmc.ncbi.nlm.nih.gov/articles/PMC11643009/", "year": 2024, "kind": "paper", "license": "open access (MDPI Materials)" }, "ueberschaar-2015": { "title": "Enabling the recycling of rare earth elements through product design and trend analyses of hard disk drives", "id": "doi:10.14279/depositonce-6368", "url": "https://depositonce.tu-berlin.de/items/99e52b20-ebd0-479d-b0ac-341c8996112c", "year": 2015, "kind": "paper", "license": "In Copyright (item page)" }, "simos-2008": { "title": "An Experimental Study of Radiation-Induced Demagnetization of Insertion Device Permanent Magnets", "id": "EPAC08 WEPC053", "url": "https://proceedings.jacow.org/e08/papers/WEPC053.pdf", "year": 2008, "kind": "paper", "license": "JACoW proceedings" }, "marechal-2006": { "title": "65 MeV Neutron Irradiation of Nd-Fe-B Permanent Magnets", "id": "EPAC06 THPCH135", "url": "https://accelconf.web.cern.ch/e06/PAPERS/THPCH135.PDF", "year": 2006, "kind": "paper", "license": "JACoW proceedings" }, "klaffky-2006": { "title": "Thermal Neutron Demagnetization of NdFeB Magnets", "id": "EPAC06 THPLS130", "url": "https://accelconf.web.cern.ch/e06/PAPERS/THPLS130.PDF", "year": 2006, "kind": "paper", "license": "JACoW proceedings" }, "usgs-mcs-2025-re": { "title": "Mineral Commodity Summaries 2025, Rare Earths", "url": "https://pubs.usgs.gov/periodicals/mcs2025/mcs2025-rare-earths.pdf", "year": 2025, "kind": "report", "license": "public domain" }, "eu-crm-page": { "title": "Critical raw materials (European Commission)", "url": "https://single-market-economy.ec.europa.eu/sectors/raw-materials/areas-specific-interest/critical-raw-materials_en", "kind": "web", "license": "EC web page" }, "pubchem-neodymium": { "title": "PubChem compound CID 23934, neodymium: molecular weight and GHS classification", "id": "CID 23934", "url": "https://pubchem.ncbi.nlm.nih.gov/compound/23934", "kind": "database" }, "pubchem-boron": { "title": "PubChem compound CID 5462311, boron: molecular weight and GHS classification", "id": "CID 5462311", "url": "https://pubchem.ncbi.nlm.nih.gov/compound/5462311", "kind": "database" }, "pubchem-iron": { "title": "PubChem compound CID 23925, iron: molecular weight and GHS classification", "id": "CID 23925", "url": "https://pubchem.ncbi.nlm.nih.gov/compound/23925", "kind": "database" }, "netl-ndfeb-lci": { "title": "NETL Life Cycle Inventory Data Process Documentation: NdFeB Permanent Magnet Manufacturing", "id": "DF_Stage1_O_NdFeB_Magnet_Manufacturing.2014.01", "url": "https://netl.doe.gov/projects/files/DF_Stage1_O_NdFeB_Magnet_Manufacturing-2014-01.pdf", "year": 2014, "kind": "report" }, "allstar-ndfeb-sds": { "title": "Allstar Magnetics Safety Data Sheet, Neodymium Iron Boron (NdFeB) Magnet", "id": "SDS NEO, Rev 1.0, 08Feb2024", "url": "https://allstarmagnetics.com/wp-content/uploads/2024/10/Neodymium-SDS.pdf", "year": 2024, "kind": "datasheet" }, "digikey-ndfeb-sds": { "title": "Safety Data Sheet (SDS/MSDS), NdFeB Magnets (Digikey supplier)", "url": "https://mm.digikey.com/Volume0/opasdata/d220001/medias/docus/5849/SDS_MSDS%20-%20NdFeB%20Magnets.pdf", "kind": "datasheet" }, "wiki-neodymium-magnet": { "title": "Neodymium magnet (Wikipedia), bonded magnet process section only", "url": "https://en.wikipedia.org/wiki/Neodymium_magnet", "kind": "web", "license": "CC BY-SA" } }, "license": "CC-BY-4.0", "url": "https://spacemushroom.com/profiles/neodymium-iron-boron/" }