{ "spore": "profile", "id": "aluminium-5019", "spore_version": "0.2", "family": "aluminium-alloys", "name": "Aluminium alloy 5019", "abbreviation": "5019", "role": "corrosion-resistant wrought aluminium-magnesium alloy", "category": "metals", "type": "aluminium", "summary": "5019 (AlMg5, also written EN AW-5019, UNS A95019, AA 5019) is a wrought aluminium-magnesium alloy with about 4.5 to 5.6 % magnesium as its main alloying element. Supplier data give a density of 2.64 g/cm3, a melting range of 575 to 630 °C, and a tensile strength of 270 to 350 MPa in the H12 form and 300 to 380 MPa in the H24 form. The supplier rates its seawater and weathering resistance as very good and says the alloy is food safe. The sources read for this profile give no yield strength and no spacecraft or flight record.\n", "best_for": "Wrought rod, tube and wire where seawater and weathering resistance matter (supplier rates both very good)", "weakest_at": "Thin data: no yield strength was found for any tested temper, and the supplier rates hard brazing as poor", "identity": { "formula": "Al-Mg alloy, AlMg5 / EN AW-5019: Mg 4.5 to 5.6, Mn 0.1 to 0.6, Cr max 0.2, Fe max 0.5, Si max 0.4, Zn max 0.2, Ti max 0.2, Cu max 0.1, other max 0.05 each and 0.15 total, Al remainder (wt%)", "cas": "", "designations": [ { "system": "UNS", "code": "A95019", "source": "totalmateria-5019", "where": "International equivalents table, row UNS, A95019" }, { "system": "AA", "code": "5019", "source": "totalmateria-5019", "where": "International equivalents table, row AA, 5019 (official)" }, { "system": "EN name", "code": "EN AW-5019", "source": "bikar-5019", "where": "Product title of the EN AW-5019 page" }, { "system": "DIN", "code": "AlMg5", "source": "bikar-5019", "where": "Designation fields, DIN (old designation) AlMg5 and Material chemically EN 573-3 AlMg5" }, { "system": "EN", "code": "3.3555", "source": "totalmateria-5019", "where": "International equivalents table, DIN 3.3555 (official)" }, { "system": "BS", "code": "N6", "source": "bikar-5019", "where": "Designation fields, United Kingdom BS N6" } ], "source": "bikar-5019", "where": "Chemical composition limits and product title on the Bikar EN AW-5019 product page; UNS and AA codes from the Total Materia equivalents table" }, "tags": { "environments": [], "stresses": [], "applications": [] }, "properties": [ { "benchmark": "density", "label": "Density, 5019", "value": 2.64, "bound": "exact", "unit": "g/cm3", "scope": "material", "conditions": { "form": "not stated", "temperature": "not stated" }, "method": "Value printed on a supplier product page", "status": "ground", "source": "bikar-5019", "where": "Density field", "source_detail": { "title": "Bikar: EN AW-5019 product page", "id": "EN AW-5019; DIN 3.3355 and AlMg5 as printed; BS N6", "url": "https://my.bikar.com/en_US/products/374_003-374-003-2", "year": 2026, "kind": "web", "license": "Supplier web page (cited, not reproduced)" } }, { "benchmark": "melting_point", "label": "Melting range, EN AW-5019 H12 listing", "value": 575, "value_high": 630, "bound": "range", "unit": "°C", "scope": "material", "conditions": { "temper": "H12 (page listing)", "form": "not stated" }, "method": "Range printed on a supplier product page (melting range row)", "status": "ground", "source": "mfgrobots-5019-h12", "where": "Physical properties, row Melting range", "source_detail": { "title": "Mfgrobots: EN 573-3 Grade AW-5019 H12, Food-Safe, Hardened AlMg Alloy", "url": "https://www.mfgrobots.com/Article/material/metal/41534.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" } }, { "benchmark": "thermal_conductivity", "label": "Thermal conductivity, EN AW-5019 H12 listing", "value": 110, "value_high": 140, "bound": "range", "unit": "W/(m·K)", "scope": "material", "conditions": { "temper": "H12 (page listing)", "temperature": "20 °C" }, "method": "Range printed on a supplier product page", "status": "ground", "source": "mfgrobots-5019-h12", "where": "Physical properties, row Thermal conductivity", "source_detail": { "title": "Mfgrobots: EN 573-3 Grade AW-5019 H12, Food-Safe, Hardened AlMg Alloy", "url": "https://www.mfgrobots.com/Article/material/metal/41534.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" } }, { "benchmark": "specific_heat", "label": "Specific heat capacity, EN AW-5019 H12 listing", "value": 904, "bound": "exact", "unit": "J/(kg·K)", "scope": "material", "conditions": { "temper": "H12 (page listing)", "temperature": "20 °C" }, "method": "Value printed on a supplier product page", "status": "ground", "source": "mfgrobots-5019-h12", "where": "Physical properties, row Specific heat capacity", "source_detail": { "title": "Mfgrobots: EN 573-3 Grade AW-5019 H12, Food-Safe, Hardened AlMg Alloy", "url": "https://www.mfgrobots.com/Article/material/metal/41534.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" } }, { "benchmark": "elastic_modulus", "label": "Modulus of elasticity, EN AW-5019 H12 listing", "value": 70, "bound": "exact", "unit": "GPa", "scope": "material", "conditions": { "temper": "H12 (page listing)", "temperature": "not stated" }, "method": "Value printed on a supplier product page", "status": "ground", "source": "mfgrobots-5019-h12", "where": "Physical properties, row Modulus of elasticity", "source_detail": { "title": "Mfgrobots: EN 573-3 Grade AW-5019 H12, Food-Safe, Hardened AlMg Alloy", "url": "https://www.mfgrobots.com/Article/material/metal/41534.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" } }, { "benchmark": "elastic_modulus", "label": "Modulus of elasticity, MSZ EN AW-5019", "value": 69, "value_high": 79, "bound": "range", "unit": "GPa", "scope": "material", "conditions": { "temperature": "not stated (band not tied to a value in the page)", "form": "not stated" }, "method": "Range printed in the physical properties section of a Total Materia page", "status": "ground", "source": "totalmateria-5019", "where": "MSZ EN AW-5019 Physical Properties, row Modulus of Elasticity", "source_detail": { "title": "Total Materia: MSZ EN AW-5019 Aluminium Alloys", "id": "EN AW-5019; AlMg5; 5019 (AA); A95019 (UNS); DIN 3.3555; standard EN 573-3", "url": "https://www.totalmateria.com/en-us/material/3214293", "kind": "database", "license": "Paywalled database (cited, not reproduced)" } }, { "benchmark": "electrical_resistivity", "label": "Electrical resistivity, MSZ EN AW-5019", "value": 0.0526, "value_high": 0.0667, "bound": "range", "unit": "Ω·mm²/m", "scope": "material", "conditions": { "temperature": "not stated (band not tied to a value in the page)", "form": "not stated" }, "method": "Range printed in the physical properties section of a Total Materia page", "status": "ground", "source": "totalmateria-5019", "where": "MSZ EN AW-5019 Physical Properties, row Electrical Resistivity", "source_detail": { "title": "Total Materia: MSZ EN AW-5019 Aluminium Alloys", "id": "EN AW-5019; AlMg5; 5019 (AA); A95019 (UNS); DIN 3.3555; standard EN 573-3", "url": "https://www.totalmateria.com/en-us/material/3214293", "kind": "database", "license": "Paywalled database (cited, not reproduced)" } }, { "benchmark": "ultimate_tensile_strength", "label": "Tensile strength, EN AW-5019 H12 rod, tube and wire", "value": 270, "value_high": 350, "bound": "range", "unit": "MPa", "scope": "material", "conditions": { "temper": "H12", "form": "rod, tube and wire (EN 573-3 and EN 754 as printed on the page)" }, "method": "Range printed on a supplier product page", "status": "ground", "source": "mfgrobots-5019-h12", "where": "Mechanical properties, tensile strength row", "source_detail": { "title": "Mfgrobots: EN 573-3 Grade AW-5019 H12, Food-Safe, Hardened AlMg Alloy", "url": "https://www.mfgrobots.com/Article/material/metal/41534.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" } }, { "benchmark": "ultimate_tensile_strength", "label": "Tensile strength, EN AW-5019 H24 tube, rod and wire", "value": 300, "value_high": 380, "bound": "range", "unit": "MPa", "scope": "material", "conditions": { "temper": "H24", "form": "tube, rod and wire" }, "method": "Range printed on a supplier product page", "status": "ground", "source": "mfgrobots-5019-h24", "where": "Mechanical properties, tensile strength row", "source_detail": { "title": "Mfgrobots: AW-5019 H24 Aluminum Alloy (EN 573-3), High Strength, Food Safe", "url": "https://www.mfgrobots.com/Article/material/metal/41537.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" } }, { "benchmark": "ultimate_tensile_strength", "label": "Tensile strength, MSZ EN AW-5019", "value": 250, "value_high": 385, "bound": "range", "unit": "MPa", "scope": "material", "conditions": { "temperature": "0 to 30 °C", "temper": "not stated", "form": "not stated" }, "method": "Range printed in the mechanical properties section of a Total Materia page", "status": "ground", "source": "totalmateria-5019", "where": "MSZ EN AW-5019 Mechanical Properties, row Tensile Strength (condition 0 to 30 °C)", "source_detail": { "title": "Total Materia: MSZ EN AW-5019 Aluminium Alloys", "id": "EN AW-5019; AlMg5; 5019 (AA); A95019 (UNS); DIN 3.3555; standard EN 573-3", "url": "https://www.totalmateria.com/en-us/material/3214293", "kind": "database", "license": "Paywalled database (cited, not reproduced)" } }, { "benchmark": "elongation", "label": "Elongation A, MSZ EN AW-5019 (minimum)", "value": 2, "bound": "lower", "unit": "%", "scope": "material", "conditions": { "temperature": "0 to 30 °C", "temper": "not stated", "gauge_length": "A as printed (A5 or A50 not stated)" }, "method": "Minimum value printed in the mechanical properties section of a Total Materia page", "status": "ground", "source": "totalmateria-5019", "where": "MSZ EN AW-5019 Mechanical Properties, row Elongation A", "source_detail": { "title": "Total Materia: MSZ EN AW-5019 Aluminium Alloys", "id": "EN AW-5019; AlMg5; 5019 (AA); A95019 (UNS); DIN 3.3555; standard EN 573-3", "url": "https://www.totalmateria.com/en-us/material/3214293", "kind": "database", "license": "Paywalled database (cited, not reproduced)" } }, { "benchmark": "brinell_hardness", "label": "Brinell hardness, MSZ EN AW-5019", "value": 65, "value_high": 95, "bound": "range", "unit": "HB", "scope": "material", "conditions": { "temperature": "0 to 30 °C", "temper": "not stated" }, "method": "Range printed in the mechanical properties section of a Total Materia page", "status": "ground", "source": "totalmateria-5019", "where": "MSZ EN AW-5019 Mechanical Properties, row Brinell Hardness (HB)", "source_detail": { "title": "Total Materia: MSZ EN AW-5019 Aluminium Alloys", "id": "EN AW-5019; AlMg5; 5019 (AA); A95019 (UNS); DIN 3.3555; standard EN 573-3", "url": "https://www.totalmateria.com/en-us/material/3214293", "kind": "database", "license": "Paywalled database (cited, not reproduced)" } } ], "corrosion": [ { "environment": "Seawater and weathering (supplier rating, no test conditions)", "headline": "The supplier rates seawater and weathering resistance of 5019 as very good.", "effect": "The corrosion properties table for the EN AW-5019 H24 listing rates seawater resistance very good and weathering resistance very good. No exposure time, test standard or corrosion rate is given.", "rating": "unknown", "conditions": { "basis": "qualitative supplier rating printed as very good; the schema has no matching level, so rating is unknown", "test": "none stated" }, "source": "mfgrobots-5019-h24", "where": "Corrosion properties section" } ], "risks": { "hazards": [ { "text": "The Hydro safety data sheet for wrought 5xxx series products classifies the product as Skin Sens. 1 (H317) and Carc. 2 (H351, inhalation). This is a product-family classification, not one written for 5019 alone.", "ghs": [ "H317", "H351" ], "source": "hydro-5xxx-sds", "where": "Section 2.1 classification and Section 2.2 label elements" }, { "text": "The same sheet lists aluminum (over 85 %) and magnesium (under 6.4 %) with the GHS classes Flam. Sol. 1 (H228) and Water-react. 2 (H261). These classes apply to the metal in the product form, and the sheet covers the whole 5xxx family.", "ghs": [ "H228", "H261" ], "source": "hydro-5xxx-sds", "where": "Section 3 composition table, rows Aluminum and Magnesium" }, { "text": "The sheet says that inhaling dusts and fumes can cause metal fume fever, and that small chips, fine turnings and dust from processing may be toxic to aquatic life.", "ghs": [], "source": "hydro-5xxx-sds", "where": "Section 2.3 other hazards" } ], "failure_risks": [ { "mode": "Dust ignition during machining", "trigger": "Machining, grinding or handling fine chips, turnings or dust", "consequence": "The Hydro sheet says metallic dusts may ignite or explode, and that dust, chips or ribbons can be ignited more easily by an ignition source or by improper machining.", "severity": "moderate", "source": "hydro-5xxx-sds", "where": "Section 2.3 and the Section 5 fire hazard text" }, { "mode": "Poor brazed joints", "trigger": "Hard brazing with or without flux, or soft brazing with flux", "consequence": "The supplier rates hard brazing poor with and without flux, and soft brazing with flux poor. Friction soldering is rated acceptable.", "severity": "moderate", "source": "mfgrobots-5019-h24", "where": "Surface treatment and joining section, brazing row" } ], "side_effects": [], "handling": [ { "text": "Avoid breathing dust or fume, and keep chips, turnings and dust under control. The Hydro sheet gives the precautionary statement 'Avoid breathing dust, fume' and says processing dust may be toxic to aquatic life.", "source": "hydro-5xxx-sds", "where": "Section 2.2 precautionary statement P261; Section 2.3" }, { "text": "Specify the temper and product form before comparing strengths. The supplier listings give different tensile ranges for H12 rod, tube and wire (270 to 350 MPa) and for H24 tube, rod and wire (300 to 380 MPa), and Total Materia gives a 250 to 385 MPa range at 0 to 30 °C.", "source": "mfgrobots-5019-h12", "where": "Mechanical properties, tensile strength rows" } ], "mitigations": [] }, "uses": [], "supply": [ { "subject": "Primary aluminium smelter production, 2025 estimate (world)", "producers": [ { "country": "China", "share_percent": 60.8, "year": 2025 }, { "country": "India", "share_percent": 5.7, "year": 2025 }, { "country": "Russia", "share_percent": 5.3, "year": 2025 }, { "country": "Canada", "share_percent": 4.5, "year": 2025 }, { "country": "United Arab Emirates", "share_percent": 3.6, "year": 2025 } ], "critical_lists": [], "recycling": "USGS: in 2025 about 3.6 million tons of aluminum were recovered from purchased scrap in the United States, about 56 % from new scrap and 44 % from old scrap. Old-scrap recovery was equivalent to about 28 % of apparent consumption.", "substitutes": [ "USGS: composites can substitute for aluminum in aircraft fuselages and wings. Copper can replace aluminum in electrical and heat-exchange applications." ], "source": "usgs-mcs2026-aluminum", "where": "World Smelter Production and Capacity table, column 2025e: China 45,000, India 4,200, Russia 3,900, Canada 3,300, United Arab Emirates 2,700, world total (rounded) 74,000 thousand t. Shares are calculated by Space Mushroom from those printed values (for example 45,000 / 74,000 = 60.8 %). Recycling and Substitutes sections." } ], "media": [], "documents": [ { "title": "Bikar: EN AW-5019 product page (composition, density, designations)", "type": "datasheet", "url": "https://my.bikar.com/en_US/products/374_003-374-003-2", "year": 2026 }, { "title": "Mfgrobots: EN 573-3 Grade AW-5019 H12 (physical and mechanical values)", "type": "datasheet", "url": "https://www.mfgrobots.com/Article/material/metal/41534.html" }, { "title": "Mfgrobots EN 573-3 Grade AW-5019 H24 (density, tensile range, corrosion, surface treatment)", "type": "datasheet", "url": "https://www.mfgrobots.com/Article/material/metal/41537.html" }, { "title": "Total Materia: MSZ EN AW-5019 Aluminium Alloys (composition limits, physical and mechanical properties, equivalents)", "type": "database", "url": "https://www.totalmateria.com/en-us/material/3214293" }, { "title": "Hydro Extrusion USA: Safety Data Sheet, Wrought Aluminum Products, 5xxx Series Alloys (revision 08/14/2018, version 2.0), copy hosted by the City of Portland", "type": "sds", "url": "https://efiles.portlandoregon.gov/record/16673616/file/document", "year": 2018 }, { "title": "USGS Mineral Commodity Summaries 2026: Aluminum", "type": "report", "url": "https://pubs.usgs.gov/periodicals/mcs2026/mcs2026-aluminum.pdf", "year": 2026 } ], "gaps": [ "No yield strength (Rp0.2) was recorded for 5019 in any temper. Total Materia prints it only behind a registration wall, the Mfgrobots pages give tensile values only, and the MakeItFrom and Wieland datasheet pages could not be read (HTTP 403 and 404).", "No thermal expansion (CTE) value is recorded. The Mfgrobots H12 page prints four values with no clear condition, and the Total Materia CTE row is behind a registration wall.", "Elongation for the Mfgrobots H12 listing is printed as 6, 7 and 8 % against A50 and A100 without a clear mapping, so it was left out. The Total Materia minimum (2 %, A) is recorded instead.", "No application or use is confirmed for 5019 in any source read here. The H24 supplier page says the alloy is food safe, but it names no device or application, so the uses list is empty.", "No flight, spacecraft, satellite or launch-vehicle record for 5019 was found.", "No corrosion test data (salt spray, ASTM G66 or G67, exfoliation, stress corrosion) for 5019 was found. Only the supplier rating very good for seawater and weathering is recorded.", "The hazard classes come from the Hydro SDS for the whole 5xxx product family, not a 5019-specific SDS. PubChem and an alloy-specific safety sheet were not read for this grade.", "Designation conflict: the Bikar page prints DIN 3.3355, and Total Materia prints DIN 3.3555. Only 3.3555 is recorded, from Total Materia, and the Bikar figure is not entered.", "The magnesium range (4.5 to 5.6 %) comes from one supplier listing (Bikar), and the Total Materia magnesium row is behind a registration wall. Mn, Si, Fe, Cu, Cr, Zn and Ti limits are from the same Bikar listing only.", "Electrical conductivity is recorded as electrical resistivity from Total Materia, so the Mfgrobots conductivity of 15,000,000 to 19,000,000 S/m was not entered as a separate property.", "The brinell_hardness benchmark name is not in property-canon.yaml. The Brinell range is recorded with that short snake_case name, as in the 2017 profile.", "The USGS 2026 aluminum summary read here does not mention a critical-minerals list, so no critical-list entry is recorded.", "Radiation effects, atomic oxygen erosion, outgassing and cryogenic properties were not looked up for this grade." ], "story": { "why": "5019 is a magnesium-rich aluminium alloy for wrought products. Supplier data give a density of 2.64 g/cm3, a tensile strength of 270 to 350 MPa in H12 rod, tube and wire, and 300 to 380 MPa in H24, with seawater and weathering resistance rated very good. The supplier also calls the alloy food safe. The sources read here name no aerospace or space application for this grade.", "uses": [], "can_do": [ { "label": "Strength", "line": "The H12 listing gives a tensile strength of 270 to 350 MPa for rod, tube and wire. The H24 listing gives 300 to 380 MPa.", "benchmark": "ultimate_tensile_strength", "scope": "material", "value": "270 to 350 MPa tensile (H12)" }, { "label": "Weight", "line": "The supplier gives a density of 2.64 g/cm3.", "benchmark": "density", "scope": "material", "value": "2.64 g/cm3" }, { "label": "Heat", "line": "The H12 listing gives a thermal conductivity of 110 to 140 W/(m·K) at 20 °C.", "benchmark": "thermal_conductivity", "scope": "material", "value": "110 to 140 W/(m·K)" }, { "label": "Sea and weather", "line": "The H24 corrosion table rates seawater and weathering resistance very good. No test conditions are given.", "scope": "material", "value": "Very good (supplier rating)" } ], "compare": "5019 is a magnesium-rich aluminium alloy with a density near 2.64 g/cm3 and a tensile strength of 250 to 385 MPa across the forms and tempers listed. The sources here give its density, stiffness and thermal figures only for this alloy, and they do not compare it with other grades numerically.", "compare_rows": [ { "label": "Density", "benchmark": "density", "scope": "material" }, { "label": "Thermal conductivity", "benchmark": "thermal_conductivity", "scope": "material" }, { "label": "Modulus of elasticity", "benchmark": "elastic_modulus", "scope": "material" } ], "handling": [ "Specify the temper and product form, because the tensile ranges differ for H12, H24 and the 0 to 30 °C values.", "Keep machining dust and fines under control. Metallic dust may ignite or explode.", "Do not rely on hard brazing. The supplier rates it poor." ], "good_for": [ "Wrought rod, tube and wire where seawater and weathering resistance matter, with the supplier rating very good for both.", "Parts that must be food safe, as the H24 supplier page states, with no further food-contact data read here." ], "watch_out": [ "Brazing is rated poor by the supplier, so brazed joints may be weak.", "No yield strength was found for any temper, so yield-based design values cannot be taken from these sources.", "The corrosion rating is qualitative and has no test conditions behind it.", "The hazard classes apply to the 5xxx family, not to 5019 alone." ], "verdict": "5019 is a corrosion-resistant Al-Mg wrought alloy by supplier rating, with a tensile range of about 270 to 380 MPa depending on temper. The sources here are thin on yield strength and on any space or flight use, and the hazard data are family-level.", "recipe": { "line": "5019 is a wrought aluminium-magnesium alloy, EN AW-5019 or AlMg5. Magnesium is the main alloying element at 4.5 to 5.6 wt%, with manganese, chromium, iron, silicon, zinc, titanium and copper as minor elements (Bikar listing, EN 573-3 limits). The sources read here do not describe how the product is made, and the composition below is the standard range, not a measured value.", "parts": [ { "name": "Aluminium", "symbol": "Al", "role": "The matrix of the alloy." }, { "name": "Magnesium", "symbol": "Mg", "role": "The main alloying element. The name AlMg5 refers to it." }, { "name": "Manganese", "symbol": "Mn", "role": "Minor alloying element." }, { "name": "Chromium", "symbol": "Cr", "role": "Minor element, limited by the standard." }, { "name": "Silicon", "symbol": "Si", "role": "Impurity or minor element, limited by the standard." }, { "name": "Iron", "symbol": "Fe", "role": "Impurity, limited by the standard." }, { "name": "Zinc", "symbol": "Zn", "role": "Minor element, limited by the standard." }, { "name": "Titanium", "symbol": "Ti", "role": "Minor element, limited by the standard." }, { "name": "Copper", "symbol": "Cu", "role": "Minor element, limited by the standard." } ] }, "risk_groups": [ { "title": "For people", "lead": "The Hydro safety data sheet for the 5xxx series gives dust, fume, skin and environmental warnings. No health data for 5019 alone were found.", "points": [ { "label": "Machining dust", "line": "Metallic dust may ignite or explode, and dusts and fumes can cause metal fume fever (Hydro SDS, 5xxx series)." }, { "label": "Skin and inhalation", "line": "The same sheet classifies the 5xxx product as a skin sensitiser (H317) and as suspected of causing cancer by inhalation (H351)." }, { "label": "Environment", "line": "Small chips, fine turnings and processing dust may be toxic to aquatic life, according to the same sheet." } ], "level": 1, "verdict": "Dust, fume and skin warnings" }, { "title": "If it fails", "lead": "The failure routes found in the sources are dust ignition, poor brazed joints and surface corrosion in service.", "points": [ { "label": "Brazing", "line": "The supplier rates hard brazing poor with and without flux, and soft brazing with flux poor. Friction soldering is rated acceptable." }, { "label": "Corrosion", "line": "The supplier rates seawater and weathering resistance very good. No test result for 5019 was found." } ] }, { "title": "Handling and storage", "points": [ { "label": "Specify temper and form", "line": "Strength ranges differ for H12 rod, tube and wire, H24 tube, rod and wire, and the 0 to 30 °C values, so state the temper and form before comparing figures." }, { "label": "Dust control", "line": "Keep machining chips and fines under control, and avoid breathing dust or fume, following the Hydro SDS." } ] } ] }, "updated": "2026-10-26", "review": { "status": "draft", "method": "assistant", "checked_values": 12, "unreachable": 4, "caveats": 5, "note": "Values were read by an AI assistant on 2026-10-26 from the pages named in each entry. Unreachable or blocked: MakeItFrom 5019 page (403), Wieland EN AW-5019 datasheets (404 and 403), Total Materia numeric rows behind a registration wall. Caveats: the composition and density come from one supplier listing; the H12 and H24 tensile ranges are supplier listings for different tempers; the hazard classes are for the whole 5xxx family; no yield strength was recorded." }, "sources": { "bikar-5019": { "title": "Bikar: EN AW-5019 product page", "id": "EN AW-5019; DIN 3.3355 and AlMg5 as printed; BS N6", "url": "https://my.bikar.com/en_US/products/374_003-374-003-2", "year": 2026, "kind": "web", "license": "Supplier web page (cited, not reproduced)" }, "mfgrobots-5019-h12": { "title": "Mfgrobots: EN 573-3 Grade AW-5019 H12, Food-Safe, Hardened AlMg Alloy", "url": "https://www.mfgrobots.com/Article/material/metal/41534.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" }, "mfgrobots-5019-h24": { "title": "Mfgrobots: AW-5019 H24 Aluminum Alloy (EN 573-3), High Strength, Food Safe", "url": "https://www.mfgrobots.com/Article/material/metal/41537.html", "kind": "web", "license": "Supplier web page (cited, not reproduced)" }, "totalmateria-5019": { "title": "Total Materia: MSZ EN AW-5019 Aluminium Alloys", "id": "EN AW-5019; AlMg5; 5019 (AA); A95019 (UNS); DIN 3.3555; standard EN 573-3", "url": "https://www.totalmateria.com/en-us/material/3214293", "kind": "database", "license": "Paywalled database (cited, not reproduced)" }, "hydro-5xxx-sds": { "title": "Hydro Extrusion USA: Safety Data Sheet, Wrought Aluminum Products, 5xxx Series Alloys (revision 08/14/2018, version 2.0)", "url": "https://efiles.portlandoregon.gov/record/16673616/file/document", "year": 2018, "kind": "datasheet", "license": "Manufacturer safety data sheet (cited, not reproduced)" }, "usgs-mcs2026-aluminum": { "title": "Mineral Commodity Summaries 2026: Aluminum", "id": "USGS MCS 2026", "url": "https://pubs.usgs.gov/periodicals/mcs2026/mcs2026-aluminum.pdf", "year": 2026, "kind": "report", "license": "public domain (USGS)" } }, "license": "CC-BY-4.0", "url": "https://spacemushroom.com/profiles/aluminium-5019/" }